Chicco Go-One Isofix Manual Del Usuario página 36

ISOFIX connectors are locked correctly into
position, checking that the two (Z) signs are
green.
7. Push the child car seat firmly against the
backrest of the car seat (diag. 14) to ensure
maximum adherence.
HOW TO FIT THE TOP TETHER
The installation of the child car seat is complete
only by fitting the Top Tether.
WARNING! Pease refer to the instructions booklet
of the vehicle to identify the locking point of the
Top Tether of the child car seat. This locking point
is marked by a specific label (diag. 15), and it may
be located in the positions indicated in the dia-
grams 16a – 16b – 16c – 16d – 16e.
WARNING! Check that the Top Tether is locked
with the correct locking device. Do not mistake
the locking device of the Top Tether with the ring
provided for securing the luggage (diag. 17).
WARNING! Insert the Top Tether between the
top part of the backrest of the car seat and the
headrest. Never insert the Top Tether above the
headrest (diag. 18).
8. After identifying the locking point, connect
the hook (DD) of the Top Tether (diag. 19).
9. Adjust the length of the Top Tether belt,
pulling the strap firmly to tension it correctly
(diag. 20). The belt is tensioned correctly when
the indicator located on the strap is green
(diag. 21).
10. Roll up the excess strap and fix it with the spe-
cific Velcro strap provided (diag. 22).
HOW TO REMOVE THE ISOFIX SYSTEM
WARNING! Remove the child from the child car
seat before proceeding to the removal of the
ISOFIX system.
1. Loosen the Top Tether by pressing the appro-
priate button BB (diag. 23), then release the
hook.
2. Roll up the Top Tether strap and fix it with the
appropriate Velcro strap (diag. 22).
3. Pull the unlocking handle of the ISOFIX sy-
stem externally (L) and, while keeping it pul-
led, detach the child car seat from the backrest
of the car seat, until the ISOFIX system is remo-
ved completely (diagrams 24a-24b).
4. Push the two red buttons inside and release
the connectors from the corresponding ISO-
FIX locking devices, located on the car seat
(diag. 25).
5. Remove from the base of the child car seat
the two caps stored in advance, and reinsert
them in the related ISOFIX connectors, paying
attention that the two ends are facing inside
(diagrams 26a-26b).
6. Push the ISOFIX system inside the base of the
child car seat, inserting it completely into the
base (diag. 27).
FITTING THE CHILD SEAT INTO THE CAR WITH
A 3-POINT SAFETY BELT
WARNING! NEVER USE THE CAR SAFETY BELT IN
ANY OTHER POSITIONS THAN THOSE INDICATED
IN THIS INSTRUCTION BOOKLET: IT COULD COM-
PROMISE THE CHILD'S SAFETY!
The holes to insert the safety belts are highlighted
on the child car seat with red signs.
WARNING! These instructions and diagrams are
for the installation of the child car seat on the
right back seat. To fit the child car seat in other
positions, carry out these operations in the same
order.
1. Place the child car seat on the desired car seat.
WARNING! Ensure there are no objects placed
between the child car seat and the car seat, or
the child car seat and car door.
2. Recline the backrest of the child car seat fully,
pulling the lever located under the seat in your
direction (Q) (Diag. 28).
3. Pull the car safety belt, sliding it in the space
between the backrest and the base of the
child car seat (Diag. 29).
4. Insert the lap section of the 3-point car safety
belt into the corresponding safety belt guides
(Diag. 30).
5. Pull out the safety belt from the other side of
the child car seat, and fasten it to the seat buc-
kle (Diag. 31).
6. Open the safety belt locking clamp (T), loca-
ted on the same side of the seat buckle, by
pressing the lever (diag. 32).
7. Insert the diagonal section of the car safety
belt into the clamp, and place the diagonal
section as shown in diag. 33. When released,
the clamp lever will automatically return to the
locked position.
8. Pull the diagonal section of the car safety belt
firmly, ensuring that the child car seat adheres
correctly to the car seat (diag. 34). If necessary,
carry out this operation exercising some pres-
sure on the child car seat with your knee.
9. Insert the upper part of the diagonal belt insi-
de the S1 guide, placing it exactly as shown in
diagram 35.
10. Pull the safety belt in the direction shown in
diagram 35 firmly, to tighten also the last part
of the belt.
11. Check that the child car seat is fitted correctly
(diag. 36).
36