Controls; How To Use; Smart Remote Temperature Sensor; Illuminated Touch Screen - Vornado TVH600 Guia Del Propietario

Controls

touch Screen controls:
Power Button
Press to turn unit ON or OFF, red light illuminates when power is ON.
heat Mode
To select the heat level you desire, press HIGH HEAT for up to 1500
watts, or LOW HEAT for up to 750 watts of maximum power.
Fan only Mode
Select FAN ONLY mode to operate the heater with no heat.
Set temperature
To select the desired room temperature, press the ( + ) or ( – ) to raise
or lower the temperature by one degree at a time.
Room temperature
The Touch Screen also indicates room temperature. The temperature
displayed is the approximate temperature at the location of the
Smart Remote. The base unit will always attempt to operate using
8 English
the sensor information from the Remote, if a signal cannot be
obtained, the base unit will function on its own. (See Smart Remote
Temperature Sensor below.)
timer
The timer function allows you to set the unit to automatically turn
off in one-hour intervals up to 9 hours. Press the ( + ) to add hours
of operation, or the ( – ) to remove hours of operation. The unit will
completely shut off when the set time has expired.
Smart Remote controls:
Power
Press the ON/OFF button to turn the unit ON or OFF.
heat Mode
Press the HEAT UP or HEAT DOWN arrows to adjust heat settings one
degree at a time.
timer
Press the TIMER UP or TIMER DOWN arrows to adjust timer by one
hour at a time.
Mode
Press the center MODE button to select HIGH HEAT, LOW HEAT or
FAN ONLY.
Battery Replacement
Screen will indicate when the batteries need to be replaced. The
Remote requires 2 AA batteries. To replace the batteries remove the
cover located on the bottom side of the remote. Note: The SMART
REMOTE SENSOR sends frequent signals to the base unit; this
uses more power than ordinary remotes so more frequent battery
replacement will be required.

Smart Remote temperature Sensor

This innovation incorporates continuous monitoring of the
temperature at the location of the remote. This temperature reading
is then transmitted back to the base unit. The TVH600 automatically
adjusts heat output and fan speed to meet and maintain the
desired temperature set. The benefit of this technology is when
you position the Smart Remote Temperature Sensor near you, the
heater will automatically adjust to meet your desired temperature
at that location. The base unit will always attempt to operate using
the sensor information from the remote, if a signal cannot be
obtained, the base unit will function on its own. Fully control the
TVH600 remotely with the Smart Remote Temperature Sensor with
illuminated screen. Turn the unit ON and OFF, select mode - FAN
ONLY, LOW HEAT or HIGH HEAT, adjust the desired set temperature
up or down, and set the automatic-off timer, all from up to 30 feet
away. As you adjust the remote, the base unit will "beep" to indicate
it has received your signal. The screen-light will dim after just a few
seconds, to minimize room illumination. The Remote does not require
"line-of-site" to operate.

illuminated touch Screen

Innovative and easy to use, the Touch Screen provides complete
control at the base unit. Just touch the screen to "wake-up" or turn
on the screen. Follow the intuitive display and touch the screen to
adjust mode, desired temperature, and timer. The Timer can be
set to turn the unit off automatically in hour intervals up to 9 hours.
The screen-light will dim after just a few seconds to minimize room
illumination. Both the remote and the base unit feature one-button
ON/OFF control.

How To Use

automatic climate control

With this unique technology, the TVH600 does not cycle on and off
like most ordinary heaters, but uses continuous variable heat and air
output to maintain the set temperature. This allows the unit to often
run on less than high power, minimizing noise and energy use, all
while maintaining your set comfort level.

Resetting Your Vornado heater

Your Vornado Heater has a multi-level safety shut-off system
designed to prevent overheating. Overheating may occur when
the inlets or outlet are blocked, a foreign object prevents the
blade from turning, or the appliance tips over. If this happens,
the safety shut-off system will cut power to the heat element
and you will need to manually reset the heater.
1. Set the POWER switch to OFF and unplug the unit.
2. Remove any obstructions.
3. Wait 5 –10 minutes, allowing the unit to cool down.
4. Plug in the unit and place in desired position.
5. Set the POWER switch to ON. Your Vornado Heater should
now function normally.
Note: If the safety shut-off system repeatedly shuts off your
heater or if it will not reset after following the above procedure,
DO NOT ATTEMPT TO DISASSEMBLE THE UNIT. Call Vornado
Consumer Services Department toll-free at 1-800-234-0604.
English
9