Cleaning And Storage; How To Clean; Storage; Operating Tips - Vornado TVH600 Guia Del Propietario

Cleaning and Storage

how to clean

† Your heater has no user serviceable parts. Do not disassemble the
unit. This will void your warranty. If service is required, return your
heater to Vornado (see WARRANTY for instructions).
† The motor is permanently lubricated and requires no oiling.
Because your heater moves a substantial
amount of air, it will need regular cleaning.
To clean follow these simple instructions:
1. Unplug the unit.
Note: Do not use gasoline, thinners,
View how to clean your
solvents or other chemicals for clean-
Vornado heater on your
ing.
mobile device.
2. Use the brush attachment on your
household vacuum cleaner to vacuum any accumulated dust off
the Front Angled Outlet Grill and Side Inlet Grill. Wipe down the
entire surface with a soft cloth.
Note: Vacuuming the outside of the heater is recommended on a
bi-weekly basis. You may also blow the heater out with high pressured
air. This can be purchased from your local hardware store.

Storage

During the off-season or after extended periods of non-use, you may
choose to store your heater. To ensure long life of the product, it is
recommended to store your heater by following these instructions:
1. Unplug power cord and bundle loosely.
2. Thoroughly clean your heater (see instructions above).
3. Cover, or place back in retail carton if available. This will prevent
the unit from accumulating dust overtime.
4. Store unit in a cool and dry location.
10 English

Operating Tips

† The Smart Remote Sensor can be turned off to save battery life or
to stop the remote from sending information to the base unit. Slide
switch on the back of the remote to the Off position to turn the
remote Off, slide the switch to On position to allow the remote to
send signals.
† The Smart Remote Sensor uses RF (radio frequency) to send the
signals, so line-of-sight is not required for the unit to function.
However, to obtain the best remote temperature sensing, position
the remote where it can sense an accurate temperature. Setting the
remote too close to other heat sources, even under a warm lamp
or in your lap, will cause the remote to sense the temperature as
warmer than the air. Inversely, setting the remote too close to cold
drafty areas, like a cold window or door, will cause the remote to
sense the temperature in the room as cooler. Placing the remote in
a drawer or other similar locations will not allow the unit to sense
the true typical temperature. Be sure to place the remote out in the
open.
Note: Even though the remote sensor may send a signal for
additional heat, the Remote Temperature Sensor cannot put the
Heater into an unsafe heat mode. Performance is always limited by
maximum power settings and multi-level safety shut-off systems. The
remote is not a toy and should only be used in the prescribed manor
intended for the use of this heater.
Note: If a room is very large or has too much heat loss, the heater
may not be able to obtain the desired set temperature at the remote,
even with the unit running continuously. To properly carry the heater,
place one hand in the back handle opening and use your other hand
to hold from the front.
† In smaller areas, you might prefer to set the unit in Low Heat mode.
In larger spaces you might prefer to set the unit on High Heat
Operating Tips
mode. A vortex beam of air will gently keep the air circulating in the
room for even, uniform heating.
† To use the TVH600 as a personal fan, press the "Fan Only" mode
on the touch screen.
† The TVH600, like any other 1500-watt electric heater, draws up to
12.5 amps of electric current. If using your TVH600 on High heat
setting causes your home circuit breaker or fuse to trip, we offer the
following suggestions:
1. Try turning off other electrical appliances that run on the same
electrical circuit as your TVH600.
2. Run the TVH600 on Low Heat mode.
3. Have your electrician add an additional circuit to your homes
electrical system. ALWAYS USE COMMON SENSE WHEN USING
THIS AND/OR ANY ELECTRICAL APPLIANCE.
† Do not use more than one heater at a time.
† Never ignore or take lightly the signs of an electrical problem, such
as:
† Warm outlet cover plates
† Sparking at outlet when plugging in or during operation
† Light flickering or dimming (indicates a shared circuit or problem)
Investigate the cause of these before continuing to use the heater.

Troubleshooting

Problem Possible Cause and Solution
Unit fails to Unit is not plugged in. Plug Power Cord into electrical
power on. outlet.
Household circuit breaker / ground fault interrupter has
tripped or blown a fuse. Reset circuit breaker / ground
fault interrupter, or replace fuse (See OPERATING TIPS).
The unit has overheated. Automatic Safety Shut-Off has
initiated (See RESETTING YOUR VORNADO HEATER).
Unit is damaged or in need of repair. Cease usage and
unplug. Contact Consumer Service for assistance.
Unit is not Ensure unit is set to High Heat and thermostat is set to
producing highest Temperature setting.
sufficient
amount of Close all doors and windows to retain heat.
heat.
Allow the unit to fully circulate the heat throughout the
room, may take several minutes.
If using remote sensor, ensure it is placed out in the open,
not too close to other heat sources or old drafts.
Unit power Power off and unplug the unit. On the bottom of the
on but there unit, there is a black disk. Push in 4-5 times ensuring it is
is no heat. not stuck. Set unit down on flat surface. Be sure power
cord is not under unit. Plug unit in and power on. Turn to
highest heat setting.
English
11