Tool Specifications; Ec Declaration Of Conformity; Noise/Vibration Information; Battery Charging - Würth STP 18-A Traducción Del Manual De Instrucciones De Servicio Original

Tool Specifications

Cordless Jigsaw
Art. No.
Rated voltage
Stroke rate at no load n
Stroke
Cutting capacity, max.
– in wood
– in aluminium
– in non-alloy steel
Weight according to
EPTA-Procedure 01:2014
Permitted ambient temperature
– during charging
2)
– during operation and during
storage
Recommended batteries
Recommended chargers
1) depending on the battery pack being used
2) Limited performance at temperatures <0 °C

Noise/Vibration Information

Sound emission values determined according to
EN 60745-2-11.
Typically the A-weighted sound pressure level of the product
is 79 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a
h
determined according to EN 60745-2-11:
Sawing chipboard: a =7.5 m/s
h
Sawing sheet metal: a =8 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main
applications of the tool. However if the tool is used for differ-
ent applications, with different accessories or insertion tools or
is poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
5700 506 X
V=
-1
min 550–2700
0
mm
mm
mm
mm
kg
°C
°C
AKKU-LI-CV-18 V/
AL 30-CV-LI
AL 60-CV-LI
(triax vector sum) and uncertainty K
2 2
, K=1.5 m/s ,
2 2
, K=1.5 m/s .
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
STP 18-A terns.
18
EC-Declaration of Conformity
23
We declare under our sole responsibility that the product
described under "Tool Specifications" complies with all appli-
120
cable provisions of the directives 2009/125/EC
20
(Regulation 1194/2012), 2011/65/EU, until
8
19 April 2016: 2004/108/EC, from 20 April 2016:
2014/30/EU, 2006/42/EC including their amendments
1)
2.2/2.4
and is in conformity with the following standards:
EN 60745-1, EN 60745-2-11.
0...+45
Technical file (2006/42/EC) at:
Adolf Würth GmbH & Co. KG, Abt. PCM
–20...+50
Reinhold-Würth-Straße 12–17
74653 Künzelsau
x,x Ah
GERMANY
www.wuerth.de
Marcel Strobel
General Manager
Künzelsau: 01.08.2015
 Use only the chargers listed in the tool specifi-
cations. Only these chargers are matched to the lithium-
ion battery of your power tool.
Note: The battery supplied is partially charged. To ensure
full capacity of the battery, completely charge the battery in
the battery charger before using your power tool for the first
time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
 Do not continue to press the On/Off switch
after the machine has been automatically
switched off. The battery can be damaged.
Observe the notes for disposal.
Dr.-Ing. Siegfried Beichter
General Manager

Battery Charging

17