Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
KIT COMPONENTS
• A) Radio trim panel with keypad • B) Radio brackets • C) Pocket • D) (14) #8 x 3/8" Phillips truss head screws • E) (2) metal inserts
• F) (9) Plastic panel clips • G) Axxess interface and wiring harness (not shown)
A
B
The World's best kits.
®
Chrysler 200 2015-2016
Chrysler 200 2017-up*
*Visit MetraOnline.com for up-to-date vehicle specific applications.
KIT FEATURES
• ISO DIN radio provision with pocket
• ISO DDIN radio provision
• Painted scratch-resistant matte black with silver trim
• Included interface shows climate and menu info on the
aftermarket radio screen
C
D
F
MetraOnline.com
(Excluding LX models with 3.0 screen)
E
© COPYRIGHT 2017 METRA ELECTRONICS CORPORATION
99-6538B
I N S TA L L AT I O N I N S T R U C T I O N S
TABLE OF CONTENTS
Dash Disassembly . .................................................2
Kit Preparation . ......................................................3
Kit Assembly
–ISO DIN radio provision with pocket . .................4
–ISO DDIN radio provision . ....................................4
Axxess Interface Installation . ............................5-11
WIRING & ANTENNA CONNECTIONS
Wiring Harness: Axxess interface and
harness included
Antenna Adapter: 40-EU55
(sold separately)
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• 5.5mm socket wrench • T-15 Torx screwdriver
• Metal cutting tool
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
REV. 8/16/17 INST99-6538B
Publicidad
Capítulos
Tabla de contenido
Manuales relacionados para Metra 99-6538B
Resumen de contenidos para Metra 99-6538B
- Página 1 Also, do not remove the factory radio with the key in the on position, or while the vehicle is running. The World’s best kits. MetraOnline.com ® © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 8/16/17 INST99-6538B...
-
Página 2: Dash Disassembly
DASH DISASSEMBLY 1. Unclip the radio trim panel, then unplug 4. Cut and remove the plastic screw tab and remove the panel. (Figure A) that secured the bracket in place. (Figure D) 2. Remove the (4) Phillips screws securing the radio, then unplug and remove 5. Unscrew the module in the sub-dash, the radio. and then slide it down a bit for the radio Remove shaded area chassis to clear. (Figure E) 3. Remove the (1) Phillips screw securing Continue to Kit Preparation the metal radio support bracket, and (Figure A) (Figure D) then remove the bracket from the sub dash. (Figure B) Note: A cutting tool is desired but you can rock the metal bracket back and forth to break it free from the weld at the top. (Figure C) (Figure B) (Figure E) (Figure C) 1.800.221.0932 MetraOnline.com... -
Página 3: Kit Preparation
KIT PREPARATION 1. Remove the (4) T-15 Torx screws securing the hazard/switch panel to the factory radio trim panel. (Figure A) 2. Remove the (2) T-15 Torx screws securing each a/c vent to the factory radio trim panel. (Figure A) 3. Attach the hazard/switch panel to the radio trim panel with keypad using the (4) #8 x 3/8” Phillips screws provided. (Figure B) 4. Attach the a/c vents to the radio trim (Figure A) panel with keypad using the (4) #8 x 3/8” Phillips screws provided. (Figure B) 5. Attach the (9) plastic panel clips to the radio trim panel with keypad. Continue to Kit Assembly (Figure B) REV. 8/16/2017 INST99-6538B... -
Página 4: Kit Assembly
KIT ASSEMBLY ISO DIN radio provision with pocket ISO DDIN radio provision 1. Attach the pocket to the radio brackets 1. Attach the radio brackets to the radio using (4) #8 x 3/8” Phillips screws using the screws supplied with the provided. (Figure A) radio. (Figure A) 2. Remove the metal DIN sleeve and trim Continue to Axxess ring from the aftermarket radio. Interface Installation 3. Attach the radio to the bracket/pocket assembly using the screws supplied with the radio. (Figure B) (Figure A) (Figure A) Continue to Axxess Interface Installation (Figure B) 1.800.221.0932 MetraOnline.com... -
Página 5: Tabla De Contenido
AXXESS INTERFACE INSTALLATION INTERFACE FEATURES INTERFACE COMPONENTS • Provides accessory power (12-volt 10-amp) • Axxess interface • Retains R.A.P. (retained accessory power) • 6538 harness • Retains the factory personalization menu and climate controls status • 18-pin harness with stripped leads • Provides NAV outputs (parking brake, reverse, and V.S.S) • 4-pin harness with stripped leads • Pre-wired ASWC-1 harness (ASWC-1 sold separately) TABLE OF CONTENTS • Retains the factory backup camera Connections to be made ......................6-8 • Retains the factory AUX-IN jack – For models without a factory amplifier ................6-7 • Retains safety chimes – For models with a factory amplifier ..................7-8 Installing the interface . -
Página 6: Connections To Be Made
CONNECTIONS TO BE MADE For models without a factory amplifier: Note: The rear-view camera input is used to display the climate control status and personalization menu. If the aftermarket radio does not have a screen with a rear-view From the 18-pin harness with stripped leads to the aftermarket radio: camera input, then there will be no visualization of the climate controls status and personalization menu, which makes adjusting the climate control impossible. An externally • Connect the (2) Red wires to the accessory wire. mounted screen could be substituted in this situation. Note: If installing an ASWC-1 (sold separately), there will be an accessory wire there to • Tape off and disregard the following (2) wires, they will not be used in this application: connect as well Blue/White, Brown... -
Página 7: For Models With A Factory Amplifier
CONNECTIONS TO BE MADE (CONT.) For models without a factory amplifier: • Tape off and disregard the following (2) wires, they will not be used in this application: White/Green, White/Red From the 18-pin harness with stripped leads to the aftermarket radio: • If retaining the factory AUX-IN jack, connect the Red & White RCA jacks to the AUX input. • Connect the (2) Red wires to the accessory wire. For vehicles with a factory rear-view camera: Note: If installing an ASWC-1 (sold separately), there will be an accessory wire there to • Keep connected the Yellow male RCA jack, to the Yellow female RCA jack. connect as well. - Página 8 CONNECTIONS TO BE MADE (CONT.) • Connect the Yellow RCA jack to the rear-view camera input. For vehicles with a factory rear-view camera: Note: The rear-view camera input is used to display the climate control status and • Keep connected the Yellow male RCA jack, to the Yellow female RCA jack. personalization menu. If the aftermarket radio does not have a screen with a rear-view This will retain the factory rear-view camera. camera input, then there will be no visualization of the climate controls status and For vehicles without a factory rear-view camera: personalization menu, which makes adjusting the climate control impossible. An externally • Connect the aftermarket rear-view camera to the Yellow female RCA jack. mounted screen could be substituted in this situation. From the 4-pin black connector: • Tape off and disregard the following (1) wire, it will not be used in this application: Brown • Connect the Orange wire, to the Orange wire on the 18-pin harness with From the 6538 harness to the aftermarket radio: stripped leads.
-
Página 9: Installing The Interface
INSTALLING THE INTERFACE FINAL ASSEMBLY With the key in the off position: • Locate the factory antenna connector in the dash, and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra. • Connect the 18-pin harness with stripped leads, and the 6538 harness, into the interface. • Test the radio and climate controls for proper operation. • Connect the 4-pin black harness into the keypad on the kit. • Audio level adjustment (amplified models only): • Connect the 6538 harness to the wiring harness in the vehicle. • With the vehicle and radio turned on, turn the volume up 3/4 of the way. Note: If using the ASWC-1 (sold separately), connect it after you program and test the interface, with the key in the off position. -
Página 10: Screen Operation
SCREEN OPERATION • Anytime the HVAC controls are pressed, the aftermarket radio will revert to the To change mode any time: rearview camera input and display the climate info. • Press < or > arrow to move through the Mode options • That screen will time out after 5-7 seconds if nothing else is changed. • Press the MENU button to force the HVAC controls to appear on screen. To get into the Personalization menu: • HVAC will stay on until MENU is pressed again • Press ^, this will highlight the gear symbol. Press “Enter” button to enter the menu. • Once in the menu, use up and down arrows to navigate through the menu options, and then press “Enter”. Note: Rear defrost, AC, and Recycle button does not cause the HVAC screen to appear. -
Página 11: Climate Control Status
CLIMATE CONTROL STATUS ATTENTION! The rear-view camera input is used to display the climate control status and personalization menu. If the aftermarket radio does not have a screen with a rear-view camera input, then there will be no visualization of the climate controls status and personalization menu, which makes adjusting the climate control impossible. An externally mounted screen could be substituted in this situation. • The use of the factory controls will interrupt the visual screen on the radio, and show the status of the changes being made instead. Note: For some aftermarket radios, there is a delay switching to the “Rear-view Camera Input”. Note: This menu has a timeout feature; after 5 seconds of no climate control use, the visual will return back to the radio. - Página 12 Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians The World’s best kits. MetraOnline.com ® © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 8/16/17 INST99-6538B...
- Página 13 Además, no quite el radio de fábrica con la llave en la posición o de encendido ni con el vehículo funcionando. The World’s best kits. MetraOnline.com ® © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 8/16/17 INST99-6538B...
-
Página 14: Desmontaje Del Tablero
DESMONTAJE DEL TABLERO 1. Desenganche el panel de la moldura 4. Corte y quite la pestaña de plástico del del radio y luego desconecte y retire tornillo que fijó el soporte en su lugar. el panel. (Figura A) (Figura D) 2. -
Página 15: Preparación Del Kit
PREPARACIÓN DEL KIT 1. Quite los (4) tornillos Torx T-15 que fijan el panel del interruptor de las luces intermitentes al panel de la moldura del radio de fábrica. (Figura A) 2. Quite los (2) tornillos Torx T-15 que fijan cada rejilla del aire acondicionado al panel de la moldura del radio de fábrica. -
Página 16: Ensamble Del Kit
ENSAMBLE DEL KIT Provisión de radio ISO DIN con cavidad Provisión de radio ISO DDIN 1. Sujete la cavidad a los soportes del 1. Una los soportes al radio usando los radio, usando (4) tornillos Phillips #8 de tornillos que vienen con el radio. 3/8”... -
Página 17: Instalación De La Interfase Axxess
INSTALACIÓN DE LA INTERFASE AXXESS CARACTERÍSTICAS DE LA INTERFAZ COMPONENTES DE LA INTERFAZ • Provee corriente de accesorio (12 voltios 10 amperes) • Interfaz Axxess • Retiene R.A.P. (corriente de accesorio retenida) • Arnés 6538 • Retiene el menú de personalización de fábrica y el estado de los controles de clima •... -
Página 18: Conexiones Que Se Deben Hacer
CONEXIONES QUE SE DEBEN HACER Para los modelos sin un amplificador de fábrica: Nota: La entrada de la cámara retrovisora se utiliza para mostrar el estado de control del clima y el menú de personalización. Si el radio de mercado secundario no tiene una pantalla Del arnés de 18 pins con conectores pelados al radio de mercado secundario: con una entrada de cámara retrovisora, entonces no se visualizará... -
Página 19: Para Los Modelos Con Amplificador De Fábrica
CONEXIONES QUE SE DEBEN HACER (CONT.) Para los modelos con amplificador de fábrica: • Coloque cinta e ignore los siguientes (2) cables; no se utilizarán en esta aplicación: blanco/verde, blanco/rojo Del arnés de 18 pins con conectores pelados al radio de mercado secundario: •... - Página 20 CONEXIONES QUE SE DEBEN HACER (CONT.) • Conecte el conector RCA amarillo a la entrada de la cámara retrovisora. Para vehículos con una cámara retrovisora de fábrica: Nota: La entrada de la cámara retrovisora se utiliza para mostrar el estado de control del •...
-
Página 21: Instalación De La Interfaz
• Localice el conector de la antena de fábrica en el tablero y realice todas las conexiones necesarias al radio. Metra recomienda el uso de un adaptador adecuado de • Conecte el arnés de 18 pins con conectores pelados y el arnés 6538 a la interfaz. -
Página 22: Operación De La Pantalla
OPERACIÓN DE LA PANTALLA • Cada vez que se presionen los controles HVAC, el radio de mercado secundario Para cambiar el modo en cualquier momento: se revertirá a la cámara retrovisora y mostrará la información del clima. • Presione la flecha < o > para avanzar por las opciones de modo •... -
Página 23: Estado De Control De Clima
ESTADO DE CONTROL DE CLIMA ¡ATENCIÓN! La entrada de la cámara retrovisora se utiliza para mostrar el estado de control del clima y el menú de personalización. Si el radio de mercado secundario no tiene una pantalla con una entrada de cámara retrovisora, entonces no se visualizará el estado de control del clima y menú... - Página 24 800-354-6782 for more information and take steps www.installerinstitute.com o llame al toward a better tomorrow. 800-354-6782 para obtener más información y avance hacia un futuro mejor. Metra recomienda MECP Técnicos certificados The World’s best kits. MetraOnline.com ® © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 8/16/17 INST99-6538B...