Layout - Toolson DKS1600 Traducción De Las Instrucciones Originales De Funcionamiento

• Before switching on, make sure that all keys and
wrenches have been removed from the tool.
• Switch off the motor and pull the power plug before
you leave the workplace.
• Electrical installation work, repairs and mainte-
nance may only be carried out by persons who
have been specially trained.
• Refit all guards and safety devices immediately af-
ter you have completed any repairs or maintenance
work.
• Be sure to observe the safety information and op-
erating and maintenance instructions issued by the
manufacturer, as well as the dimensions listed in
the Technical Data.
• It is imperative to observe the accident prevention
regulations in force in your area as well as all other
generally recognized rules of safety.
• Note the information published by your profession-
al associations (VBG 7j).
• The saw is intended to be used indoors only.
• Workpieces that are smaller than the saw blade
guard can cause injuries to the hands or fingers.
Use suitable aids!
• Avoid cramped hand positions when guiding in the
workpiece and avoid positions in which slipping
could lead to your hand making direct contact with
the saw blade.
• Always fit the saw blade with the teeth facing in the
direction of the sawing table.
• Always set the correct blade tension to prevent the
saw blades from jerking.
• Be especially careful when cutting material with ir-
regular cut profiles.
• Exercise particular caution when cutting round ob-
jects such as rods and pipes. These can roll down
into the saw blade and cause the teeth to catch.
Use a wedge to brace such workpieces.
• The teeth can become caught in the kerf when
the workpiece is pulled back, especially if sawings
have filled in (blocked) the kerf. In this case, you
should switch the saw off, pull the power plug, clear
the kerf with a wedge, and remove the workpiece.
• Never leave the work area without having already
switched the saw off. Wait until the saw stops mov-
ing completely.
• Do not position, join, or construct any parts on the
work table while the saw is running.
• Only switch the saw on after you have removed any
remaining material and tools from the work table.
Leave only the workpiece to be machined and any
aids (e.g. wedges) on the work table.
• Always wear safety goggles!
• Keep your fingers at a safe distance from the saw
blade.
• Carefully guide the workpiece and keep it steady
at all times.
• Never leave the work area without having already
switched the saw off.
• Do not let your familiarity with the saw allow you
to be careless. Carelessness can lead to severe
injuries within a fraction of a second.
20 GB
Safe work
• When transporting the electric tool, only use the
transport devices (Abb.1 Pos.10).
• Never use the protective devices for handling or
transport.
• Make sure that the lower part of the saw blade is
covered during transport, e.g. by the protective de-
vice.
• Working position is always laterally of the saw
blade.
Do not lose this safety information.
Warning! This electric tool generates an electromag-
netic field during operation. This field can impair ac-
tive or passive medical implants under certain condi-
tions. In order to prevent the risk of serious or deadly
injuries, we recommend that persons with medical
implants consult with their physician and the manu-
facturer of the medical implant prior to operating the
electric tool.
3. Layout (Figs. 1-12)
1 Blow-off device
2 Mounting
3 Knurled screw
4 Holder
5 Saw blade guard
6 Saw table
7 Cover, left
8 Bearings
9 Tightening lever
10 Arm
11 Graduated scale
12 Locking lever
13 Extractor connection
14 ON/OFF switch
15 Speed regulator
16 Assembly points
17 Sawblade
18 Retaining device
19 Upper adapter
20 Allen key, 3 mm
21 Angle (Not supplied)
22 Storage box for saw blades
23 Lower adapter
24 Saw blade holder, top
25 Saw blade holder, bottom
26 Table insert
27 Pointer
28 Screw
29 Bracket
30 Work lamp
31 ON / OFF switch work lamp
32 Setting gauge for saw blades without pin