Supplied Package; Proper Use; Technical Data - Toolson DKS1600 Traducción De Las Instrucciones Originales De Funcionamiento

4. Supplied package

• Open the packaging and take out the equipment
with care.
• Remove the packaging material and any packaging
and/or transportation braces (if available).
• Check to see if all items are supplied.
• Inspect the equipment and accessories for trans-
port damage.
• If possible, please keep the packaging until the end
of the guarantee period.
Important
The equipment and packaging material are not toys.
Do not let children play with plastic bags, foils or small
parts. There is a danger of swallowing or suffocating!
• Fretsaw
• Saw blade guard
• Blow-off device
• Spare saw blade (2x) (for wood and plastics)
• Allen key, 3 mm
• Original operating instructions

5. Proper use

The fretsaw was designed to cut square-edged tim-
ber or other workpieces such as Plexiglas, glass fiber
reinforced plastic, foam, rubber, leather, and cork. Do
not use this saw to cut round materials. Round mate-
rials can easily become jammed. Risk of injury! Parts
can be catapulted!
The equipment may only be used for the tasks it is
designed to handle. Any other use is deemed to be a
case of misuse. The user/operator and not the manu-
facturer will be liable for any damage or injuries of any
kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial appli-
cations. Our warranty will be voided if the equipment
is used in commercial, trade or industrial businesses
or for equivalent purposes.
• The equipment is to be operated only with suitable
saw blades. It is prohibited to use any type of cut-
ting-off wheel.
• To use the equipment properly you must also ob-
serve the safety information, the assembly instruc-
tions and the operating instructions to be found in
this manual.
• All persons who use and service the equipment
have to be acquainted with these operating instruc-
tions and must be informed about the equipment's
potential hazards.
• It is also imperative to observe the accident preven-
tion regulations in force in your area.
• The same applies for the general rules of health
and safety at work.
• The manufacturer will not be liable for any changes
made to the equipment nor for any damage result-
ing from such changes.
Residual risks
Even if you use this electric power tool in accordance
to instructions, certain residual risks cannot be elimi-
nated. The following hazards may arise in connection
with the equipment's construction and layout:
• Lung damage if no suitable protective dust mask
is applied
• Damage to hearing if no suitable ear protection is
applied
• Contact with the blade in the uncovered cutting
zone
• Injuries (cuts) when changing the blade
• Crushed fingers
• Kickback
• Tilting of the workpiece due to inadequate support
• Touching the blade
• Catapulting of pieces of timber and workpieces

6. Technical data

Mains voltage:
Power input:
Stroke rate:
Protection type:
Stroke:
Base area:
Tilting range of table:
Table size:
Length of saw blade
approx.:
Reach:
Max. cutting height at
90°:
Max. cutting height at
45°:
minimum size work
piece wxh:
maximum size work
piece wxh:
Weight:
Operating mode S6 30%:
Continuous operation with idling (cycle time 10 min-
utes). To ensure that the motor does not become ex-
cessively hot, it may only be operated for 30% of the
cycle at the specified rating and must then be allowed
to idle for 70% of the cycle.
Noise emission values
Sound
Sound values were measured in accordance with EN
61029.
220-240 V~/50 Hz
80 Watt (S1) 120 Watt
(S6 30%)
500-1700 min
-1
IP 20
12 mm
630 x 295 mm
0° - 45°
415 x 255 mm
134 mm
406 mm
50 mm
22 mm
100 x 22 mm
400 x 50 mm
12,7 kg
GB 21