Warranty; Disposal And Recycling; Regulations; Technical Data - stayer ISL120K Manual De Instrucciones

5.3 Warranty

Warranty card
Included in the documentation that
accompanies this equipment, you should find the warranty
card. You should fill out the card completely and return to
vendor with a copy of purchasing receipt or invoice and you
should receive a receipt.
Note: If you cannot find the warranty card within the
documentation, you must ask for it through your supplier.
The warranty is limited only to manufacturing defects and
expire if pieces have been removed or manipulated or
repaired other than the manufacturer.

5.4 Disposal and recycling

The machine, accessories and packaging should be sorted
for environmental-friendly recycling.
Only for EC countries:
Do not dispose of power tools into household waste!
According the European Guideline 2002/96/EC
for Waste Electrical and Electronic Equipment
and its implementation into national right, power
tools that are no longer usable must be collected
s e p a r a t e l y a n d d i s p o s e d o f i n a n
environmentally correct manner.
Subject to change without notice.
Battery packs/batteries:
Li-ion:
Please observe the instructions in section "Transport".
Do not dispose of battery packs/batteries
into household waste, fire or water. Battery
packs/batteries should be collected,
r e c y c l e d o r d i s p o s e d o f i n a n
environmental-friendly manner.
Only for EC countries:
Defective or dead out battery packs/batteries must be
recycled according the guideline 91/157/EEC.

6. Regulations

6.1 Technical Data

= Battery
= Voltage
= Battery Power
= charging time
= no load speed
rpm
= Torque
Ins = Inserting chuck
= Wood cut
max
= Steel cut
max
= Weigth
ENGLISH
15
L = Sound power level
WA
L = Sound pressure level
A
P
= Vibration
The values given are valid for nominal voltages [U] 230/240 V ~
50/60 Hz - 110/120 V ~ 60Hz. For lower voltage and models for
specific countries, these values can vary. Please observe the
article number on the type plate of your machine. The trade
names of the individual machines may vary.
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 87 dB(A); Sound power level 98 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
determined according to EN 60745:
Impact tightening of fasteners of the maximum capacity of the tool:
2
a =9m/s , K =1.5 m/s .
h
The vibration emission level given in this information sheet has
been measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with another. It
may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main
applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the
vibration emission may differ. This may significantly increase the
exposure level over the total working period.
An estimation of the level of exposure to vibration should also take
into account the times when the tool is switched off or when it is
running but not actually doing the job. This may significantly
reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the
effects of vibration such as: maintain the tool and the accessories,
keep the hands warm, organisation of work patterns.

6.2 EU declaration of conformity

The undersigned: STAYER IBERICA, S.A.
With address at:
Calle Sierra de Cazorla, 7
Área Empresarial Andalucía - Sector 1
28320 PINTO (MADRID)
Tel.: +34 902 91 86 81 / Fax: +34 91 691 91 72
CERTIFIES
That the machine:
Type: IMPACT WRENCH
Models: ISL120
We declare under our sole responsibility that this product is
in conformity with the following standards or standardized
documents: EN 60745 according to EU Regulations
2004/108/CE, 2006/42/CE
Ramiro de la Fuente
Managing Director
15
h
2