Tabla de contenido
Publicidad
WORKING BIT UNTIL IT REACHES THE CORRECT POSITION).
RELEASE THE MOUNTING SLEEVE, WHICH WILL FASTEN THE
WORKING BIT.
THE WORKING TOOL IS REMOVED IN THE REVERSE ORDER TO
THE INSTALLATION.
WHEN SHORT SCREWDRIVER TIPS AND BITS ARE USED, THE
ADDITIONAL ADAPTER FOR SCREWDRIVER BITS MUST BE USED.
ADJUSTABLE HANDLE
THE SCREWDRIVER HANDLE CAN BE POSITIONED STRAIGHT (IN
THE AXIS OF THE SPINDLE) OR AT AN ANGLE. THE HANDLE IS
MAINTAINED IN EACH OF THE POSITION WITH A LATCH.
Press the handle lock button (5).
Rotate the handle by 180
around the axis (fig. E).
0
Make sure the handle lock button (5) snapped and the handle is
properly secured.
SPINDLE BRAKE
THE CORDLESS SCREWDRIVER IS EQUIPPED WITH AN
ELECTRONIC BRAKE, WHICH STOPS THE SPINDLE IMMEDIATELY
AFTER THE SWITCH BUTTON IS RELEASED. THE BRAKE ENSURES
PRECISION WHEN TIGHTENING OR DRILLING AND PREVENTS
FREE SPINDLE ROTATION AFTER IT IS SWITCHED OFF.
OPERATION / ADJUSTMENTS
SWITCHING ON /SWITCHING OFF
SWITCHING ON - PRESS THE SWITCH BUTTON (9).
SWITCHING OFF - RELEASE THE PRESSURE ON THE SWITCH
BUTTON (9).
SPEED ADJUSTMENT
The drilling or tightening speed can be controlled during work by
increasing or decreasing pressure on the switch button (9). The
speed control allows for a slow start, which prevents a drill from
slipping, when holes are drilled in a dry wall or glazed wall, while it
helps to control the operation during tightening and loosening.
TORQUE ADJUSTMENT
THE SETTING OF THE TORQUE CONTROL RING (2) TO A
SELECTED POSITION LOCKS THE CLUTCH TO A SPECIFIED
AMOUNT OF TORQUE. WHEN THE SET AMOUNT OF TORQUE IS
REACHED, THE OVERLOAD CLUTCH WILL BE AUTOMATICALLY
DISCONNECTED. THIS PREVENTS FROM OVERTIGHTENING OF A
SCREW OR DAMAGING THE TOOL.
DIFFERENT VALUES OF TORQUE ARE APPLIED TO VARIOUS
TYPES OF SCREWS AND MATERIALS. THE HIGHER IS THE
NUMBER CORRESPONDING TO A GIVEN POSITION, THE HIGHER
IS THE TORQUE.
Set the torque control ring (2) to a specified amount of torque (fig.
F).
The work should be started with a lower value of torque.
Increase the torque gradually until appropriate value is set (range
0 ÷ 10).
Higher settings should be used to loosen screws.
The ability to select proper torque settings comes with practice.
The setting of the torque control ring to the drilling position
deactivates the overload clutch.
ROTATION DIRECTIONS - LEFT AND RIGHT
THE DIRECTION OF SPINDLE ROTATIONS IS SELECTED BY
MEANS OF THE ROTATION DIRECTION SWITCH (6) (FIG. G).
LEFT ROTATIONS - SET THE ROTATION DIRECTION SWITCH (6)
IN THE EXTREME LEFT POSITION.
RIGHT ROTATIONS - SET THE ROTATION DIRECTION SWITCH (6)
IN THE EXTREME RIGHT POSITION.
* It is reserved that in some cases the position of the rotation
direction switch in relation to rotations may be different than
described. Refer to graphic signs located on the rotation direction
switch or on the tool casing.
The middle position of the rotation direction switch (6) is a safe
position that prevents accidental activation of the power tool:
The screwdriver can not be activated in this position.
Bits and drills are replaced in this position.
Before the tool is activated, make sure the rotation direction switch
(6) is set to a correct position.
The direction of rotations can not be changed, when the
screwdriver spindle rotates.
Long-lasting drilling with low torque of the spindle may overheat
the motor. Periodical breaks in operation must be taken or
allow the tool to operate with maximum speed without load
for approximately 3 minutes.
OPERATION AND MAINTENANCE
CLEANING AND MAINTENANCE
IT IS RECOMMENDED TO CLEAN THE TOOL AFTER EACH USE.
DO NOT USE ANY CLEANING AGENTS, AS THEY MAY DAMAGE
PARTS OF THE TOOL MADE OF PLASTIC.
CLEAN THE CASING WITH DRY CLOTH.
VENTING SLOTS IN THE MOTOR HOUSING SHOULD BE CLEANED
ON A REGULAR BASIS NOT TO OVERLOAD THE TOOL.
THE TOOL SHOULD ALWAYS BE STORED IN A DRY PLACE AND
OUT OF REACH OF CHILDREN.
ALL TYPES OF FAULTS AND DEFECTS SHOULD BE ELIMINATED
BY AN AUTHORISED SERVICE OF THE MANUFACTURER.
RATED DATA
Cordless screwdriver
Parameter
Battery voltage
Battery type
Battery capacity
Idle speed:
Tool chuck:
10
SPECIFICATIONS
Value
7,2 V DC
Li-ion
1500 mAh
230 min
-1
Hexagonal 1/4" (6.35 mm)
Publicidad
Tabla de contenido
