Walimex Pro Light Shooter 360 TTL Manual De Instrucciones página 28

无线闪光拍摄：光学传输
单元，可以控制 2、设置主控单元的闪光模式
D7100/D7000/
在禁用主控单元闪光模式下，只有从属单元的闪光灯闪光。
获取多种照明效
Canon:
• Press function button 4 until <Menu3> is shown in the display.
单元。因此，在
• Then press function button 1 until <CH> is shown in the display. Use the
adjusting wheel to select one of the 32 channels.
• Confirm the choice with the <Set> button.
1
按功能按钮 4 <
组别，再按功能按
M/A/B/C
钮
3< MODE
元的闪光模式可以在
之间进行切换，选择
TTL/M
其中一种作为主控单元的闪
光模式。
Nikon:
• Press function button 3.
3、设置通讯频道
• Choose from channel 1 to 4.
如果在拍摄现场不止一个无线闪光系统，您可以通过更改通讯频道来防止信号干扰。保证主控单元和从属单元设置为
• Confirm the choice with the <Set> button.
相同的频道编号即可。
1
按下功能按钮 3<
6.6.2 Fully automatic trigger in TTL mode 转调节旋钮从 1至4中 选择频
道。
Canon:
• Set the Light Shooter to camera and switch to master (wireless).
• Switch the other camera flash to slave (wireless).
• Make sure both are set to the same channel.
• Place the camera and flashes as per the above illustration.
• Set the master flash to <ETTL> mode. The slave flash will automatically be
set to <ETTL> for shots.
• Check that the master flash is ready. The light must be on. As soon as the
slave flash is ready, the light will flash at 1 second intervals.
54
2
> 选择 按" MODE/ 锁定"按钮可切换
至 模式。
RPT
选择主控单
>
OFF/i-
2
>，旋 按下<SET>设置按钮确定。
C C H H
• Check that it is working. To do this, press the master test button <
The slave flash will then be triggered. If the flash is not triggered, change
the angle to the master flash and change the distance to the master flash.
Nikon:
• Set the Light Shooter 360TTL/N to camera and switch to master (wireless).
You can set the mode to M/A/B/C individually.
• Set the second Light Shooter 360TTL/N camera flash to slave (wireless).
The slave can be allocated to group A/B/C.
• Make sure both are set to the same channel.
• Place the camera and flashes as per the above illustration
• Check that the master flash is ready. The light must be on. As soon as the
slave flash is ready, the light will flash at 1 second intervals.
• Check that it is working. To do this, press the master test button <
无线闪光拍摄：光学传输
slave flash will then be triggered. If the flash is not triggered, change the
angle to the master flash and change the distance to the master flash.
4 i-TTL: 全自动无线闪光拍摄
、
If the flash does not work or triggers on its own, this could be because of lit
computer screens nearby or the light from fluorescent tubes.
使用一个从属单元的自动闪光拍摄
2
1
设置主控单元。 设置从属单元。
● 将安装在相机上的AD360II-N ● 将要被无线控制AD360II-N
设为主控单元。(第15页) 设为从属单元。(第15页)
● M/A/B/C都可独立设置为
● 可以选择
TTL。
>.
>. The
3
检查传输频道。
● 将主控单元和从属单元的频
道设为一致。(第1 页) 6
A/B/C 。
55