Replacement Parts; Troubleshooting - Stanley FATMAX FMC792 Manual Del Usuario

Rotate the stall release lever (6) on the tool to release the
u
driver blade and clear the jam. If tool is still jammed follow
the 9 steps listed below:
Pull pusher downward until it locks in place then tip the
u
tool over so the nails slide freely out from the bottom of
the magazine.
Lift the jam clearing latch (7) then pull up to open front
u
door (14).
Remove bent nail, using pliers if necessary.
u
If driver blade is in the down position, insert screwdriver
u
or other rod into nosepiece and push driver blade back
in position.
Close the front door and engage the wire form (13)
u
under the two arms (15) on the contact trip. Push jam
clearing latch down (7) until it locks in place.
Reinsert nails into magazine (see Loading the Tool).
u
Pull pusher (10) downward until the nail follower (C1)
u
falls behind the nails as shown in figure C.
Reinsert battery pack.
u
Disengage trigger lock-off (2), allowing the trigger to be
u
actuated.
Warning!If a jam occurs, the tool will disable itself and will
require you to reset it. To do so, follow instructions on clearing
the jammed nail. Next remove battery pack and then reinsert
battery pack. The tool will now be operational.
Note!Should nails continue to jam frequently in contact trip,
have tool serviced by an authorized Stanley Fat Max service
center.
Cold Weather Operation
When operating tools at temperatures below freezing:
Keep tool as warm as possible prior to use.
u
Actuate the tool 5 or 6 times into scrap lumber before
u
using.
Hot Weather Operation
Tool should operate normally. However, keep tool out of direct
sunlight as excessive heat can deteriorate bumpers and other
rubber parts resulting in increased maintenance.
Belt Hook (Fig. I-J)
Warning!Remove nails from magazine before making any
adjustments or servicing this tool. Failure to do so may result
in serious injury.
(Original instructions)
Remove battery pack from tool, and engage trigger lock-
u
off.
With a screwdriver remove screw from hang hook cavity
u
on the base of the tool (16).
Place the front lip of the hang hook (11) into the cavity on
u
the base of the tool (16) as shown in Figure I.
Secure the hang hook (11) with the supplied screw (17)
u
and firmly tighten with a screwdriver as shown in Figure J.
Replace battery pack.
u

Replacement parts

Warning!To reduce the risk of personal injury, disconnect
battery pack from tool and engage trigger lock-off before
performing maintenance, or clearing a jammed nail.
The tool comes equipped with a spare no mar tip located on
the side of the nail magazine.
To replace the no mar pad, simply pull off the old no mar
u
pad and refit the new no mar pad onto the contact trip.
Use only identical replacement parts. For a parts list or to
order parts, visit our service website at www.stanley.eu/3co.
uk. You can also order parts from your nearest
Stanley Fat Max Factory Service Center or Stanley Fat Max
Authorized Warranty.

Troubleshooting

If your appliance seems not to operate properly, follow the
following instructions.
If this does not solve the problem, please contact your local
Stanley Fat Max repair agent.
Warning! Before proceeding, unplug the appliance.
Problem Possible Cause
Unit will not start. Battery pack not
installed properly.
Battery pack not
charged.
Trigger lock-off is
engaged.
Tool doesn't Motor stops running
actuate. after 2 seconds.
(Headlights on,
motor does not
run)
Tool doesn't Low battery charge or
actuate. damaged battery.
(Headlights
flash)
Tool doesn't Jammed fastener / tool
actuate. stalled.
(Headlights flash
continuously)
Jammed mechanism
Tool doesn't
actuate.
((Headlights on,
motor runs,
driver blade
stuck down)
ENGLISH
Possible Solution
Check battery pack
installation.
Check battery pack charging
requirements.
Disengage trigger lock-off.
Normal operation; release
trigger or contact trip and
re-depress.
Charge or replace battery.
Remove the battery, rotate the
stall release lever. Clear the
jammed fastener, and reinsert
battery pack.
See authorized service center.
See authorized service center.
11