Stanley FATMAX FMC792 Manual Del Usuario página 9

Longest life and best performance can be obtained if
u
the battery pack is charged when the air temperature is
between 18°- 24°C. DO NOT charge the battery pack in
an air temperature below +4.5°C, or above +40.5°C. This
is important and will prevent serious damage to the battery
pack .
The charger and battery pack may become warm to touch
u
while charging. This is a normal condition, and does not
indicate a problem. To facilitate the cooling of the battery
pack after use, avoid placing the charger or battery pack
in a warm environment such as in a metal shed, or an
uninsulated trailer
If the battery pack does not charge properly:
u
Check current at receptacle by plugging in a lamp or
u
other appliance
Check to see if receptacle is connected to a light switch
u
which turns power off when you turn out the lights.
Move charger and battery pack to a location where the
u
surrounding air temperature is approximately 18°-
24°C.
If charging problems persist, take the appliance, battery
u
pack and charger to your local service center.
The battery pack should be recharged when it fails to
u
produce sufficient power on jobs which were easily done
previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also
charge a partially used pack whenever you desire with no
adverse affect on the battery pack.
Foreign materials of a conductive nature such as, but
u
not limited to, steel wool, aluminium foil, or any buildup
of metallic particles should be kept away from charger
cavities. Always unplug the charger from the power supply
when there is no battery pack in the cavity. Unplug charger
before attempting to clean.
Do not freeze or immerse charger in water or any other
u
liquid.
Warning! Shock hazard. Do not allow any liquid to get inside
charger. Never attempt to open the battery pack for any
reason.
If the plastic housing of the battery pack breaks or cracks,
return to a service center for recycling.
Installing and removing the battery pack from the
appliance
Warning! Make certain the lock-off button is not engaged to
prevent switch actuation before removing or installing battery.
To install battery pack
Insert battery (A1) into appliance until an audible click is
heard (Figure A). Ensure battery pack is fully seated and fully
(Original instructions)
latched into position.
To remove battery pack
Depress the battery release button (B1) as shown in Figure B
and pull battery pack out of appliance.
Operation
Warning! Read the section titled Nailer Safety Warnings at
the beginning of this manual. Always wear eye and ear protec-
tion when operating this tool.
Keep the nailer pointed away from yourself and others. For
safe operation, complete the following procedures and checks
before each use of the nailer.
Warning! To reduce the risk of personal injury, disconnect
battery pack from tool and engage trigger lock-off before
performing maintenance, clearing a jammed nails, leaving
work area, moving tool to another location or handing the tool
to another person.
Warning! Keep fingers AWAY from trigger when not driving
fasteners to avoid accidental firing. Never carry tool with finger
on trigger.
Wear proper eye, hearing and respiratory protection.
u
Remove battery pack from tool and engage trigger lock-
u
off.
Lock the pusher in the back position and remove all nail
u
strips from the magazine.
Check for smooth and proper operation of contact trip and
u
pusher assemblies. Do not use tool if either assembly is
not functioning properly.
Never use a tool that has damaged parts.
u
To operate the nailer
Warning! The contact trip needs to be depressed followed by
a full trigger pull for each nail followed by a release of both the
contact trip and trigger after each nail.
Warning!The battery should always be removed and the
trigger lock-off engaged whenever any adjustments are made
or when tool is not in use.
Fully depress contact trip against the work surface.
u
Fully pull trigger and motor will start. (nail will drive into
u
work surface).
Release trigger.
u
Lift contact trip off work surface.
u
Repeat the above 4 steps for next application
u
Preparing the tool
Warning! NEVER spray or in any other way apply oil, lubri-
cants or cleaning solvents inside the tool. This can seriously
affect the life and performance of the tool.
Warning! The battery should always be removed and the
trigger lock-off engaged whenever any adjustments are made
or when tool is not in use.
Read the Safety Instruction section of this manual.
u
ENGLISH
9