Chicco FULLY Instrucciones De Uso página 20

Do not tumble dry
Do not iron
Do not dry clean
MAINTENANCE
If necessary, lubricate the moving parts with dry silicone
lubricant. Regularly check the condition of the wheels and
clean off all dust and sand. To avoid friction that may com-
promise the correct functioning of the stroller, make sure
that all plastic parts that slide on the metal tubes are free of
dust, dirt and sand. Keep the stroller in a dry place.
FIRST ASSEMBLY OF THE STROLLER
1. Press the grey button on the left circular joint (Fig.1).
2. Then extend the structure completely, by opening the
front leg tube and the handle tube until hearing a locking
click (fig. 2-2A).
3. Fit the front wheel into the appropriate hole until hearing
a locking click (Fig. 3). Repeat the same operation for the
other wheel.
4. To mount the rear wheel, insert the wheel pin into the
hole on the rear leg tube (Fig. 4), ensuring that the flat
part of the pin corresponds with the hole in the frame.
Repeat the same operation for the other wheel.
WARNING: Before using the stroller, make sure that the
wheels are well secured to the structure.
5. The front part of the basket has a shaped area. Mount the
storage basket by wrapping the shaped part on the front
metal bar and securing it with the velcro (Fig. 5), thread the
straps located on the front part of the basket through the
"D''-shaped rings located on the front legs of the stroller,
securing the straps with the press stud buttons on both
sides (fig. 5A). Wrap the textile flap on the tube on the rear
part of the frame (fig. 5B) and close it on itself with the snap
buttons (Fig. 5C). Thread the straps located on the rear part
of the basket through the "D''-shaped rings located on the
front legs of the stroller and close the buttons (Fig. 5D).
6. Complete the assembly of the stroller by positioning the
mudguards on the rear wheels (Fig. 6). Each mudguard
features a symbol, repeated on the rear legs, indicating
the correct coupling for mounting.
ASSEMBLY OF THE SEAT: STROLLER CONFIGURATION
The packaging includes the disassembled stroller frame
and closed seat.
7. To fit the seat on the stroller, open it (Fig. 7 – 7A) until you
hear the locking click (Fig. 7B).
8. Fasten the buckle A, placed externally in the area of the
seat near the child's feet (Fig. 8); Then fasten buckles B,
located under the seat (Fig. 8A).
9. To attach the seat, place the two hooks (Fig. 9) in the
relative slots located inside the articulated joints of the
stroller (fig. 9A) until hearing a locking click.
WARNING: Make sure the seat is installed properly by pulling
it upwards.
10. The seat can be assembled on the stroller in both di-
rections: in forward facing configuration (Fig. 10) and
parent facing configuration (fig. 10A).
11. To remove the seat from the frame, press the side but-
tons and pull upward (fig. 11).
WARNING: These operations must not be performed
when the child is inside the seat.
WARNING: Do not remove the seat from the stroller when
the child is inside it.
HOODS
The seat features an extensible hood.
12. To adjust the hood (in three positions) push it forward
as far as it goes (Fig. 12). To increase the extension, open
the zipper (Fig. 12A) and then push forward.
To close the hood, act on the button on the central part
of the handle and push it towards the backrest (Fig. 12B).
13. To remove the hood, open the zipper near the tube of
the backrest completely and press the buttons located
outside on the hood's joints; then pull the hood up-
wards (Fig. 13).
To fasten the hood, follow the steps described above in re-
verse order.
WARNING: The canopy must be fixed to both sides of the
stroller. Ensure that the canopy is correctly fastened.
SEAT ADJUSTMENTS
Once the seat is fitted on the frame, it can be reclined in
three different positions.
14. The entire seat can be adjusted by pressing simultane-
ously the buttons located above the central articulated
joint (fig. 14).
15. The angle of the backrest can be modified compared to
the seat by acting on the adjuster located behind the
backrest (Fig. 15).
16. It is possible to adjust the leg rest in various positions, by
pressing simultaneously the side buttons (Fig. 16).
17. The stroller is equipped with removable bumper bar. To
remove it, press the buttons located on the sides (Fig. 17).
To position and remove the child, unhook the bar from one
side only (Fig. 17A).
WARNING: Always fasten the safety harnesses. The bar IS
NOT a device for containing your child.
WARNING: The bar must not be used to lift the stroller
with the child inside of it.
HOW TO USE THE SAFETY HARNESS
The stroller is equipped with a retaining system with five
anchoring points, consisting of two shoulder straps, two
adjusting holes, a waist belt and a crotch strap with buckle,
already assembled.
18. WARNING: To adapt the belts to the body of the child,
use the shoulder straps, passing them through the two
regulation holes (Fig. 18). After laying the child in the
stroller, fasten the belts by threading first the two forks
inside the shoulder straps' slot (fig. 18A) and then intro-
duce them inside the crotch strap buckle (fig. 18B); ad-
just the length of the straps, ensuring that they adhere
to the child's shoulders and body correctly.
19. To unfasten the waist belt, press and pull the lateral
prong (Fig. 19).
20. The waist belt must always be passed through the 2
D-shaped rings on the sides of the stroller seat (fig. 20).
WARNING: Always use the restraint systems. For the safety of
your child use all five fixing points of the safety harness belts.
REMOVING THE SAFETY BELTS
The safety belts can be removed (to be washed or used in
20