Working With The Power Tool - Flex LDC 1709 FR Manual Del Usuario

LDC 1709 FR/LD 1709 FR/LDC 1509 FR
 To switch off the power tool, release the
switch rocker by pressing the rear end.
Adjusting the guard (LDC 1709 FR/
LDC 1509 FR)
klqb
The brush ring should protrude over the sanding
pad by approx. 0–1 mm. To compensate for
wear on the diamond sanding pad, the height
of the guard can be adjusted.
 Loosen the screw connection on the guard.
 Adjust the guard by turning it to the required
height.
 Tighten the screw connection.
Using a dust extraction system
klqb
It is recommended to use the FLEX special
extractor S 47 M.
 Guide the extraction hose through the hose
support and attach it to the connection on
the guard.
 Connect extraction hose to the dust
extraction system. Follow the operating
instructions for the dust extraction system!
Check the attachment! If required, use an
appropriate adapter.
klqb
fÑ=óçìê=Çìëí=Éñíê~Åíçê=êÉèìáêÉë=~=ëéÉÅá~ä=
ÅçååÉÅíáçå=EáKÉK=~=ÅçååÉÅíáçå=çíÜÉê=íÜ~å=íÜÉ=
PO ããLPS ãã=ëí~åÇ~êÇ=ÅçååÉÅíáçå=ïÜáÅÜ=
áë áåÅäìÇÉÇ=ïáíÜ=íÜÉ=ÉäÉÅíêáÅ=éçïÉê=íççäFI=
Åçåí~Åí=óçìê=Çìëí=Éñíê~Åíçê=ëìééäáÉê=íç=çÄí~áå=
íÜÉ=~ééêçéêá~íÉ=~Ç~éíÉêK

Working with the power tool

t^okfkd>
qÜÉ=êçí~íáåÖ=ë~åÇáåÖ=ÇáëÅ=ãìëí=åçí=ÅçãÉ=áåíç=
Åçåí~Åí=ïáíÜ=ëÜ~êé=éêçàÉÅíáåÖ=çÄàÉÅíëK=a~åÖÉê=
çÑ=âáÅâÄ~Åâ>=a~ã~ÖÉ=íç=ë~åÇáåÖ=é~ÇK=fÑ=íÜÉ=
ë~åÇáåÖ=é~Ç=áë=Ç~ã~ÖÉÇ=çê=ëÉîÉêÉäó=ïçêåI=
áí ãìëí=ÄÉ=êÉéä~ÅÉÇK
`^rqflk>
eçäÇ=íÜÉ=ÉäÉÅíêáÅ=éçïÉê=íççä=ïáíÜ=ÄçíÜ=Ü~åÇë>=
1. Attach sanding tool.
2. Connect dust extraction system.
3. Insert mains plug.
4. Switch on dust extraction system.
5. Switch on the device.
6. Place the renovation sander on the work
surface.
The brush ring (LDC 1709 FR/LDC 1509 FR)
or the rubber extraction ring (LD 1709 FR)
must be flush with the work surface.
21