Skil 0738 Manual Original página 158

c) Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool's
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a hazardous
situation.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack.
b) Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
c) When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fire.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or
burns.
6) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
SPECIFIC SAFETY INSTRUCTIONS FOR HEDGE
CUTTERS
GENERAL
• This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the tool by a person responsible for
their safety
• Ensure that children do not play with the tool
• Only use the tool in daylight or with appropriate artificial
lighting
• Always remove battery from tool
- whenever leaving the tool unattended
- before clearing jammed material
- before checking, cleaning or working on the tool
- after striking a foreign object
- whenever the tool starts vibrating abnormally
• Do not trim hedges when they are wet
• Never use the tool with a defective protective guard
BEFORE USE
• Before using the tool for the first time, it is recommended
to receive practical information
• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the charger
• Check the functioning of the tool before each use and,
in case of a defect, have it repaired immediately by a
qualified person; never open the tool yourself
• Before use, thoroughly inspect the cutting area and
remove all foreign objects that could be entangled in the
cutting blades (such as stones, nails, wire fences, metal
plant supports)
DURING USE
• Do not operate the tool when barefoot or wearing open
sandals; always wear sturdy shoes and long trousers
• Keep other persons and animals at a distance of 5
metres when using the tool
• Take a secure stance when working (do not overreach,
especially when using steps or a ladder)
• Keep all parts of the body away from the cutting
blades, do not remove cut material or hold material
to be cut when blades are moving, and make sure
the switch is off when clearing jammed material (a
moment of inattention while operating the tool may result
in serious personal injury)
• Keep the (extension) cord away from the cutting
area (during operation the cord may be hidden in shrubs
and can be accidentally cut by the blades)
• Hold the power tool by the insulated gripping
surfaces only, because the cutting blades may
contact hidden wiring or its own cord (cutting blades
contacting a "live" wire may make exposed metal parts
of the power tool "live" and could give the operator an
electric shock)
• Always ensure that the ventilation openings are kept
clear of debris
• In case of electrical or mechanical malfunction,
immediately switch off the tool or unplug charger from
power source
AFTER USE
• Carry the tool by the handle with the cutting blades
stopped and, when transporting or storing the tool,
always mount the blade cover (proper handling of the
tool will reduce possible personal injury from the cutting
blades)
CHARGING/BATTERIES
• Charge battery only with the charger that is supplied
with the tool
• Do not touch the contacts in the charger
• Do not charge battery in damp or wet environments
• When charging the battery, place the charger on a flat
non-flammable surface and away from combustible
materials
• Store tool/charger/battery in locations where
temperature will not exceed 40°C or drop below 0°C
• Do not use charger when damaged; take it to one of the
officially registered SKIL Service Stations for a safety
check
6