Chamberlain LiftMaster Professional 9747E Manual De Instrucciones

FEATURES
For use with any LiftMaster 433MHz garage door opener.
Personalized Password:
Up to 10,000 possible combinations. Password can be easily changed if desired.
Temporary Password:
Can be added for visitors or service persons. This temporary password can be limit-
ed to a programmable number of hours or a programmable number of entries.
Rolling Code: While your password remains constant until you change it, the code
between the Keyless Entry and the receiver changes with each use, randomly
accessing over 100 billion new codes.
Operation: Opener activates when 4-digit password and ENTER button is pressed. If
wrong numbers are accidentally pressed, correction can be made immediately. The
ENTER button will transmit only the lastfour digits. The keypad will blink for 15 sec-
onds after the password is transmitted. During that time the ENTER button can be
used to stop or reverse the door travel.
One Button Close: Opener can be closed by pressing only the ENTER button if the one but-
ton close feature has been activated. This feature has been activated at the factory. To activate or
deactivate this feature press and hold buttons 1 and 9 for 10 seconds. The keypad will blink twice
when the one button close is active. The keypad will blink four times when one button close is
deactivated.
SETTING THE PERSONAL ENTRY PASSWORD
We recommend that you program your password now, before you install the Keyless
Entry. Then you can test the reception at the mounting location before you proceed
further.
USING THE MULTI- FUNCTION DOOR CONTROL
1. Enter a four digit personal identification
number (PIN) of your choice on the keypad.
Then press and hold ENTER.
2. While holding the ENTER button, press and
hold the LIGHT button on the Multi-Function
Door Control.
3. Continue holding the ENTER and LIGHT
buttons while you press the push bar on the
Multi-Function Door Control (all three buttons
are held).
4. Release buttons when the motor unit lights
blink. It has learned the code. If light bulbs
are not installed, two clicks will be heard.
To prevent possible SERIOUS INJURY or DEATH from a moving gate or
garage door:
• Install Keyless Entry Control within sight of the garage door, out of reach of
children at a minimum height of 1.5 m, and away from all moving parts of
door.
• ALWAYS keep remote controls out of reach of children. NEVER permit chil-
dren to operate, or play with remote control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly adjust-
ed, and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed. NEVER
permit anyone to cross path of moving gate or door.
USING THE "LEARN" BUTTON
Wireless Keyless Entry with
rolling code Model 9747E
9 1 9 1
7 3 7 3
5 KG 5 KG
1. Press and release the learn button on motor unit. The
learn indicator light will glow steadily for 30 seconds.
2. Within 30 seconds, enter a four digit personal identifi
cation number (PIN) of your choice on the keypad.
Then press and hold the ENTER button.
3. Release the button when the motor unit lights blink. It
has learned the code. If light bulbs are not installed,
two clicks will be heard.
INSTALLATION
Choose a convenient location for installation.
Install out of the reach of children at a mini-
mum height of 1.5 m, away from all moving
parts of door.
For a one-piece door, choose the optional
location shown in the illustration to avoid
injury as the door swings up and out.
Test the reception of the Keyless Entry by
operating your opener from the selected loca-
tion. Change the location if necessary.
Remove the battery cover to access the bot-
tom mounting hole.
- Insert a small phillips screw driver into the
small hole at the
bottom of the cover and gently pull outward to loosen.
- Slide the cover down to remove. Remove battery.
Center the keypad at eye level against the selected location.
Mark 4-1/4" (10.8 cm) up the centerline from the bottom and drill
a 1/8" (3.2 mm) pilot hole. Install top mounting screw, allowing
1/8" (3.2 mm) to protrude above surface. Position keypad on
screw head and adjust for snug fit. With cover open so bottom
mounting hole is visible, use a punch to mark hole. Remove
keypad and drill 1/8" (3.2 mm) pilot hole. Replace keypad and
complete installation with bottom screw, using care to avoid cracking plastic housing.
Do not over tighten. To replace battery cover slide up and snap it into place.
The Keyless Entry Battery
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
The battery should produce power for at least one
year. Replace when the Keyless Entry illumination
becomes dim or it doesn't stay on after a keystroke.
Dispose of old battery properly.
TO CHANGE AN EXISTING, KNOWN PIN
If the existing PIN is known, it may be changed by one person without using a ladder.
1. Press the four buttons for the present PIN, then press and hold the # button.
The opener light will blink twice. Release the # button.
2. Press the new 4-digit PIN you have chosen, then press ENTER.
The motor unit lights will blink once when the PIN has been learned.
Test by pressing the new PIN, then press ENTER. The door should move.
TO SET A TEMPORARY PIN
You may authorize access by visitors or service people with a temporary 4-digit PIN.
After a programmed number of hours or number of accesses, this temporary PIN
expires and will no longer open the door. It can be used to close the door even
after it has expired. To set a temporary PIN:
1. Press the four buttons for your personal entry PIN (not the last temporary PIN),
then press and hold the * button. The opener light will blink three times. Release
the button.
2. Press the temporary 4-digit PIN you have chosen, then press ENTER.
The opener light will blink four times.
3. To set the number of hours this temporary PIN will work, press the number of
hours (up to 255), then press * .
3. To set the number of times this temporary PIN will work, press the number of
times (up to 255), then press #.
The opener light will blink once when the temporary PIN has been learned.
Test by pressing the four buttons for the temporary PIN, then press Enter. The door
should move. If the temporary PIN was set to a certain number of openings, remem-
ber that the test has used up one opening.To clear the temporary password,
repeat steps 1-3, setting the number of hours or times to 0 in step 3.
SPECIAL NOTE: The temporary password can ONLY be programmed to keypads
working on a LiftMaster Garage Door Opener. It WILL NOT work on keypads pro-
grammed to an external receiver. The temporary password will continue to CLOSE
the door even after the time has expired. To eliminate this, program a new
temporary password into the keypad.
i
en
Keyless Typical
Entry Installation
Exterior Front Wall
1-Piece or
Sectional Door
Door Jamb Edge
(Optional)
Door Jamb Face
(SECTIONAL DOOR ONLY)
KEYLESS ENTRY MUST BE
INSTALLED WITHIN
SIGHT OF THE DOOR
Bottom
mounting hole
Battery
Battery
Cover
Pb Cd Hg
OR
0845 602 4285