Using The Fader Start Function - Pioneer DJM-900SRT Manual De Instrucciones

Depending on the playing status of Serato DJ or the DJ player (off air, scratch-
ing, playing in reverse, etc.), it may not be possible to receive the GRID
information.
2 Press the [ON/OFF] button of [BEAT EFFECTS] or touch the
[X-PAD].
The effect is added to the sound in tempo with the track being played.
When the [QUANTIZE] button is pressed again, the QUANTIZE function turns
off.

Using the FADER START function

When this unit and a computer on which Serato DJ is running are connected by
USB cable, such operations as starting playback of tracks in Serato DJ can be con-
trolled using this unit's fader.
Connect this unit and a computer on which Serato DJ is running beforehand.
In the same way, when this unit and a Pioneer DJ player are connected by LAN
cable, such operations as starting playback of the DJ player can be controlled using
this unit's fader.
Connect the Pioneer DJ player and this unit beforehand. For instructions on con-
necting, see Connecting input terminals on page 11.
For instructions on setting the player numbers of Pioneer DJ players, see About PRO
DJ LINK on page 15.
The fader start function can be switched on and off for all DJ players all at once. For
the switching procedure, see Changing the settings on page 24.
The FADER START function cannot be used when attempting to perform
DVS control while Serato DJ is set to the Absolute mode. When one of the
[FADER START (1, 2, 3, 4)] buttons is pressed while the Absolute mode is set,
that button flashes then turns off.
Start playback using the channel fader
1 Set the [CROSS FADER ASSIGN (A, THRU, B)] selector switch
to [THRU].
2 Press one of the [FADER START (1, 2, 3, 4)] buttons.
Select the channel to be started with the fader start function.
For Serato DJ
— [Fader Start 1] button: Selects [DECK 3].
— [Fader Start 2] button: Selects [DECK 1].
— [Fader Start 3] button: Selects [DECK 2].
— [Fader Start 4] button: Selects [DECK 4].
3 Set the channel fader to the nearest position towards you.
4 Set a cue in Serato DJ or on the DJ player.
The track cues to the cue point and the pause mode is set.
5 Move the channel fader away from you.
Playback of the track in Serato DJ or the DJ player starts.
If you set the channel fader back to the original position, the player instanta-
neously returns to the cue point already set and pauses playback (back cue).
Start playback using the crossfader
1 Set the [CROSS FADER ASSIGN (A, THRU, B)] selector switch
to [A] or [B].
2 Press one of the [FADER START (1, 2, 3, 4)] buttons.
Select the channel to be started with the fader start function.
For Serato DJ
— [Fader Start 1] button: Selects [DECK 3].
— [Fader Start 2] button: Selects [DECK 1].
— [Fader Start 3] button: Selects [DECK 2].
— [Fader Start 4] button: Selects [DECK 4].
3 Set the crossfader.
Set to the edge opposite the side on which the channel you want to use with the
fader start function is set.
4 Set a cue in Serato DJ or on the DJ player.
The track cues to the cue point and the pause mode is set.
5 Set the crossfader.
Playback of the track in Serato DJ or the DJ player starts.
If you set the crossfader back to the original position, the player instantaneously
returns to the cue point already set and pauses playback (back cue).
Using the LINK MONITOR function
Check [Use "LINK MONITOR" of Pioneer DJ Mixers.] at [File] > [Preferences]
> [Audio] in rekordbox beforehand. Also refer to the rekordbox operating
instructions.
16
En
1 Connect headphones to the [PHONES] terminal.
2 Connect a computer on which rekordbox is installed.
For instructions on connections, see Connecting input terminals on page 11.
3 Selecting the track to be monitored with rekordbox.
4 Press the [CUE] button for [LINK].
The track selected with rekordbox is output from the headphones.
When the [CUE] button is pressed again, monitoring is canceled.
The same operation as at Monitoring sound with headphones (steps 3 to 5) can
be performed.
Using the SOUND COLOR FX function
These are effects that change in association with the [COLOR] control.
1 Press one of the [SOUND COLOR FX] selection buttons.
This selects the type of effect.
The button that was pressed flashes.
Even if one of the [SOUND COLOR FX] selection buttons is already selected,
when a different button is selected and pressed, that button is selected.
For the types of effects, see Types of SOUND COLOR FX effects on page 19.
The same effect is set for [CH1] to [CH4].
2 Turn the [COLOR] control.
The effect is applied to the channel(s) for which the control(s) was (were) pressed.
Canceling the SOUND COLOR FX effect
Press the [SOUND COLOR FX] selection button that is flashing.
The effect is canceled.
Using the BEAT EFFECT function
This function lets you instantaneously set various effects according to the tempo
(BPM = Beats Per Minute) of the currently playing track.
Main unit display
1
1
2
MIC
AUTO
3
TAP
7
9
a
Effect display
The name of the selected effect is displayed.
1
section
Channel select
The name of the channel to which the effect is applied is displayed.
2
display section
[AUTO] lights when the BPM measurement mode is set to the auto
AUTO (TAP) mode.
3
[TAP] lights when in the manual input mode.
When in the auto mode, this displays the automatically detected
BPM value.
BPM value display When the BPM cannot be detected, the previously detected BPM
4
(3 digits) value is displayed and flashes.
When in the manual input mode, this displays the BPM value that
was input manually.
This lights when Serato DJ is running and the QUANTIZE func-
tion can be used. It also lights when playing a track that has been
analyzed with rekordbox and the QUANTIZE function can be used
5
GRID
in combination with the DJ player. It flashes or is off when the
QUANTIZE function cannot be used.
This is always lit.
6
BPM
This displays the parameters specified for the individual effects.
When the [BEAT
Parameter display fraction is displayed for 1 second.
7
section When a value outside the parameter range is specified with the
[BEAT ,
flashes.
% (ms) These light according to the units for the different effects.
8
Beat display
This lights according to the selected beat number position.
9
section
Touch display
This lights when the [X-PAD] is touched.
a
section
1 Press [AUTO/TAP] button.
Select the BPM measurement mode.
CH SELECT
2 3 4
A B
MST
PARAMETER
4
5
GRID
6
BPM
%
8
ms
, ] button is pressed, the corresponding beat
] button, the value does not change and the display