WINTER INACTIVITY
In areas where winter temperatures frequently drop below 0°C,
during periods in which the hot tub is not used, proceed as follows:
Disconnect the power from the main electric board (and the
Jacuzzi® heat pump where used).
Completely drain the hot tub via the drain valve, which is to
be left open, and the possible gate valve installed on the auxil-
iary drain (if installed; refer to the pre-installation instructions).
The emptying of the hot tub is not complete; stagnant water on
the seats and bottom of the tub can be eliminated with a sponge,
while water left in the hoses can be sucked out through the hydro-
massage and suction intakes, using a liquid-suction pump. It is ad-
visable to empty the pump as well via the appropriate drain plug.
Model with Jacuzzi® heat pump: fully empty the heat
pump, slackening the fittings connecting to the system; follow
the instructions provided for the hot tub, to suck up any remain-
ing water.
IMPORTANT
In cold climates, where temperatures drop well below
0°C, all residual water should be eliminated from the cir-
cuit.
Remove and clean the filter cartridge and store in a dry place.
Cover the hot tub to keep it clean.
Model with Jacuzzi® heat pump: leave the fittings loose,
so as to eliminate any condensation.
Before you use the hot tub again, refer to the chapter on op-
erating checks for first start-up.
Model with Jacuzzi® heat pump: before using the heat
pump again, remember to tighten the fittings again.
In areas where temperatures only occasionally drop below
0 °C, the hot tub can be left in operation, since it is equipped
with an anti-freeze protection that ensures that a minimum
water temperature is maintained (see the chapter "Setting water
temperature", which contains paragraphs on maintaining the mini-
mum water temperature and preventing freezing of water in the
pipes - "Smart Winter" mode).
MAINTENANCE OF WOOD PARTS
Some of the Jacuzzi® spa covering panels and accessories are
made of natural wood, treated with advanced products which
enhance the natural beauty and ensure protection against atmos-
pheric agents.
The panels and accessories first receive a coat of stain, to give the
wood an even shade. Then two coats of synthetic oil are applied,
which give the piece a natural and particularly warm appearance.
Cleaning
Maintenance varies according to the location of the spa and/
or accessories (sheltered from or exposed to the elements).
In any case, you should periodically wash the surfaces with fresh
water and neutral detergent. Then rinse.
Do not use detergents that contain alcohol, scale-removal sub-
stances, ammonia, abrasive products or bleach.
Do not use wax or polish.
Renewal
At least once a year (or less, depending on the conditions the
wood surfaces are exposed to), do the following:
Lightly sand the surface with an abrasive sponge (or sandpa-
per, grain 320). Do not press too hard, especially near protruding
parts (corners and so on).
Remove all dust. Use a soft-bristled brush to apply a layer of
synthetic oil, first crosswise and then along the entire height of
the panel.
Do not work in direct sunlight, nor if the temperature is espe-
cially cold.
If necessary, remove any excess oil using a microfiber cloth.
Let dry for about an hour (at 20°C).
Note: tools can be washed with turpentine for subsequent reuse.
If more extensive restoration is require (for example, if the pro-
tective layer has been damaged in depth), you should thorou-
ghly sand the entre surface all the way down to the bare wood.
Apply a coat of stain if there are marked differences in shades.
Then apply two to three coats of synthetic oil as necessary, fol-
lowing the same method described for the renewal phase.
Note: make sure that, between one coat and the nest, the product
has dried completely. This normally takes 1 to 2 hours at an am-
bient temperature of about 20 °C).
For all special maintenance, it is advisable to contact specialized
personnel.
ATTENTION: sanding residue, tools and rags used to apply
the product may self-ignite if exposed to the air. Keep the re-
cipients (immerged in water) in tightly closed metallic contai-
ners and dispose of them immediately. Comply with current
applicable regulations.
CLEARRAY™ MAINTENANCE
The Clearray™ filtering system uses a UV lamp. The lamp must be
replaced after one year.
CAUTION
Do not carry out any UV lamp cleaning or replacement
operations. Staring at the UV lamp when on may cause
serious harm to sight or even blindness. Contact the
dealer or an authorised assistance centre.
22