Sección 9 − Lista De Partes; Piezas De Repuesto Recomendadas - Miller Spectrum 875 Auto-Line Manual Del Usuario

.
Una lista completa de piezas se encuentra electrónicamente en línea en www.MillerWelds.com

9-1. Piezas de repuesto recomendadas

Item Dia. Part
No. Mkgs. No.
. . . . . . . . . . . . . . . . 234843
. . . . . . . . . . . . . . . . 227877
. . . . . . . . . . . . . . . . 234838
. . . . . . . . . . . . . . . . 234930
. . . . . . . . . . . . . . . . 213619
. . . . . . . . . . . . . . . . 213620
. . . . . . . . . . . . . . . . 234132
. . . . . . . . . . . . . . . . 234134
. . . . . . . . . . . . . . . . 234136
. . . . . . . . . . . . . . . . 234138
To maintain the factory original performance of your equipment, use only Manufacturer's Suggested
Replacement Parts. Model (located on nameplate on front of unit) and serial number (located on outside
bottom of plasma cutter base) is required when ordering parts from your local distributor.
Standard Cutting
60A
Drag Shield
212 730
Shield
212 732
40A
Drag Shield
212 730
Extended Cutting
60A
Deflector
212 736
40A
Deflector
212 736
60A
Shield
212 731
To maintain the factory original performance of your equipment, use only Manufacturer's Suggested
Replacement Parts. Model (located on nameplate on front of unit) and serial number (located on outside
bottom of plasma cutter base) is required when ordering parts from your local distributor.
OM-242 880 Página 46
SECCIÓN 9 − LISTA DE PARTES
Description
Piezas de repuesto recomendadas
. . Label, Ice 60t Consumables
. . Filter, Air Element . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . Cable, Work 20 Ft 6 Ga W/Clamp And Male Dinse
. . Cable, Work 50 Ft 6 Ga W/Clamp And Male Dinse
. . Clamp, Work 300 A Stl Chrome Pld W/Copper Contacts
. . Contact Tip, Work Clamp 300amp Copper
. . ICE−60T 20 Ft Hand Held Replacement Torch Or
. . ICE−60T 50 Ft Hand Held Replacement Torch
. . ICE−60TM 25 Ft Machine Replacement Torch
. . ICE−60TM 50 Ft Machine Replacement Torch
Retaining
Cup Tip Electrode
212 733 219 676 212 724
(Machine Cutting)
Retaining
Cup Tip
212 733 212 725
Retaining
Cup Tip
212 733 219 682
Retaining
Cup Tip
212 733 212 729
Gouging
Retaining
Cup Tip
212 733
219 680
Cup Installation: Do not overtighten — finger-tight only.
Ilustración 8-1. Consumable Parts For ICE-60T
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Swirl Ring O-Ring
212 734 212 735
Apply silicone
grease (169 231)
before installing.
ICE-60T
CONSUMABLES
CAUTION
FAILURE TO REPLACE
WORN TIP OR
ELECTRODE MAY
DAMAGE TORCH AND
VOID WARRANTY.
S
Turn off power before
checking torch parts.
S
Check before each use and
hourly during operation.
234 843-B
. . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
Quantity
1
1
1
1
1
2
1
1
1
234 843-B