Structure And Functions - Lavorwash FREE EVO 50E Manual De Instrucciones

Mount the brushes or scraper disks (with the abra-
sive disks) that are suitable for the surface and
work involved.
Mount the squeegee, check that it is solidly at-
tached and connected to the suction hose and that
the drying blades are not too worn.
Make sure that the recovery tank is empty. If not,
empty it completely.
Check and completely close the detergent solution
release control.
Fill the detergent solution tank with a mix of clean
water and non-foaming detergent in an adequate
concentration through the anterior hole. Leave 2
cm between the mouth of the plug and the level of
the liquid.
☞
( ) To avoid risks, become familiar with the ma-
chine movements, carrying out test runs on a large
surface without obstacles.
To obtain the best results in terms of cleaning and
equipment service life, you should do the following
simple but important operations:
- Identify the work area, moving all possible obsta-
cles out of the way; if the surface is very extensive,
work in contiguous and parallel rectangular areas.
- Choose a straight work trajectory and begin work-
ing from the farthest area to avoid passing over
areas that have already been cleaned.

6.2 STRUCTURE AND FUNCTIONS

PHOTO A Model E
1 GENERAL ON/OFF SWITCH
2 BRUSH MOTOR SWITCH
3 SUCTION MOTOR SWITCH
PHOTO B Model E
1 POWER SUPPLY CABLE
2 BRUSH PLATE LIFT/LOWER LEVER
3 SQUEEGEE LIFT/LOWER LEVER
4 BRUSH OPERATION LEVER
5 RECOVERY TANK DRAIN HOSE
PHOTO C Model B - (DC 24V)
1 BRUSH MOTOR SWITCH
1A BRUSH MOTOR OPERATION LED
2 SUCTION MOTOR SWITCH
2A SUCTION MOTOR OPERATION LED
3 BATTERY POWER TEST
3A GREEN LED - FULL BATTERY CHARGE
3B YELLOW LED - 50% BATTERY CHARGE
3C RED LED - BATTERY DISCHARGED
PHOTO D Model B - (DC 24V)
1 GENERAL ON / OFF KEY SWITCH
2 BRUSH OPERATION LEVER
3 BRUSH PLATE LIFT/LOWER LEVER
4 SQUEEGEE LIFT/LOWER LEVER
5 BRUSH MOTOR THERMAL BREAKER
6 RECOVERY TANK DRAIN HOSE
7 BATTERY CONNECTOR
PHOTO E Model BT/T - (DC 24V with traction)
1 BATTERY POWER TEST
1A GREEN LED - FULL BATTERY CHARGE
1B YELLOW LED - 50% BATTERY CHARGE
1C RED LED - BATTERY DISCHARGED
2 FORWARD/REVERSE INDICATOR
3 REDUCE SPEED SWITCH
3A TRACTION SPEED 1
3B TRACTION SPEED 2
3C TRACTION SPEED3
3D TRACTION SPEED 4
4 INCREASE SPEED SWITCH
5 BRUSH MOTOR SWITCH
5A BRUSH MOTOR OPERATION LED
6 SUCTION MOTOR SWITCH
6A SUCTION MOTOR OPERATION LED
PHOTO F Model BT/T - (DC 24V with traction)
1 GENERAL ON / OFF KEY SWITCH
2 FORWARD/REVERSE TRACTION OPERA-
TION LEVER
3 BRUSH PLATE LIFT/LOWER LEVER
4 SQUEEGEE LIFT/LOWER LEVER
5 BRUSH MOTOR THERMAL BREAKER
6 TRACTION MOTOR THERMAL BREAKER
7 RECOVERY TANK DRAIN HOSE
8 BATTERY CONNECTOR
PHOTO G
Model B - BT/T - (DC 24V without and
with traction)
BATTERY CONNECTION DIAGRAM
PHOTO H
Model B - BT/T - (DC 24V without and
with traction)
1 BATTERY COMPARTMENT OPENING
LEVER
2 SOLUTION TANK FILLING OPENING
PHOTO I
Model B - BT/T - (DC 24V without and
with traction)
1 OPENING CLIP SPRING
2 BATTERY COMPARTMENT WITH 12V
BATTERIES
3 BATTERY CONNECTION WIRING
PHOTO L
Model B - BT/T - (DC 24V without
and with traction)
1 BUILT-ON BATTERY CHARGER
35