gefran 40T 48 Manual De Instrucciones página 4

Sr
Serial settings
(o
Device identification code
s. p
Serial interface protocol
ba
Baudrate selection
pt
Parity selection
In
Inputs setting
Type of probe, signal and
tP
scale of main input
tP PROBE without
TYPE dec. point
Probe: TC
0 TC J °C 0/1000
1 TC J °F 32/1832
2 TC K °C 0/1300
3 TC K °F 32/2372
4 TC R °C 0/1750
5 TC R °F 32/3182
6 TC S °C 0/1750
7 TC S °F 32/3182
8 TC T °C -200/400
9 TC T °F -328/752
10 TC B °C 44/1800
11 TC B °F 111/3272
12 TC E °C -100/750
13 TC E °F -148/1382
14 TC N °C 0/1300
15 TC N °F 32/2372
16 TC LGOST °C 0/600
17 TC LGOST °F 32/1112
18 TC U °C -200/400
19 TC U °F -328/752
20 TC G °C 0/2300
21 TC G °F 32/4172
22 TC D °C 0/2300
23 TC D °F 32/4172
24 TC C °C 0/2300
25 TC C °F 32/4172
26 TC °C Custom
27 TC °F Custom
Probe: RTD
28 PT100 °C -200/850
29 PT100 °F -328/1562
30 JPT100 °C -200/600
31 JPT100 °F -328/1112
Probe: PTC - NTC
32 PTC °C -55/120
33 PTC °F -67/248
34 NTC °C -10/70
35 NTC °F 14/158
0 ... 247
SP Serial Protocol
0 CENCAL GEFRAN
1 MODBUS RTU
bA Baudrate
0 1200
1 2400
2 4800
3 9600
4 19200
_Pt Parità
0 No parity
1 Odd
2 Even
• TC / LIN input parameters
tP PROBE
TYPE
Probe: Voltage + Current
36 0...60mV
37 0...60mV
38 12...60mV
39 12...60mV
with
40 0...20mA
dec. point
41 0...20mA
42 4...20mA
0.0/999.9
43 4...20mA
32.0/999.9
44 0...10V
0.0/999.9
45 0...10V
32.0/999.9
46 2...10V
0.0/999.9
47 2...10V
32.0/999.9
48 0...5V
0.0/999.9
49 0...5V
32.0/999.9
50 1...5V
-199.9/400.0
51 1...5V
-199.9/752.0
52 0...1V
44.0/999.9
53 0...1V
111.0/999.9
54 200mV...1V
-100.0/750.0
55 200mV...1V
-148.0/999.9
Probe: Custom PT100 - PTC - NTC
0.0/999.9
56 PT100
32.0/999.9
JPT
0.0/600.0
57 PTC
32.0/999.9
58 NTC
-199.9/400.0
-199.9/752.0
0.0/999.9
32.0/999.9
0.0/999.9
32.0/999.9
Max. non-linearity error for
0.0/999.9
thermocouples (TC),
32.0/999.9
resistors (PT100) and
Custom
Custom
thermistors (PTC, NTC)
-199.9/850.0
-199.9/999.9
The error is calculated as
-199.9/600.0
deviation from theoretical
-199.9/999.9
value and is expressed as
percentage of full scale (in
-55.0/120.0
-67.0/248.0 °C)
-10.0/70.0
14.0/158.0
• Sr
s. i
Virtual instrument inputs
Inputs
Bits
Ex.:
To manage PV and IN from serial line, the
code to be set in S.I is 48.
s. o
Virtual instrument outputs
Outputs OUTW
Bits
Ex.:
To manage OUT1, OUT2 and OUT3 from serial
line, the code to be set in S.0 is 19.
s. U
Interf. KEYB
Bits 7 6
Ex.: 0 1
To manage KEYB and LED OUT1 from serial line, the code
to be set in S.U is 65
without with
decimal point decimal point
-1999/9999 -199.9/999.9
linear custom linear custom
-1999/9999 -199.9/999.9
linear custom linear custom
-1999/9999 -199.9/999.9
linear custom linear custom
-1999/9999 -199.9/999.9
linear custom linear custom
-1999/9999 -199.9/999.9
linear custom linear custom
-1999/9999 -199.9/999.9
linear custom linear custom
-1999/9999 -199.9/999.9
linear custom linear custom
-1999/9999 -199.9/999.9
linear custom linear custom
-1999/9999 -199.9/999.9
linear custom linear custom
-1999/9999 -199.9/999.9
linear custom linear custom
custom custom
custom custom
custom custom
S, R range 0...1750°C; error < 0.2% f.s. (t > 300°C)
for other range; error < 0.5% f.s.
T error < 0.2% f.s. (t > -150°C)
B range 44...1800°C; error < 0.5% f.s. (t > 300°C)
range 44,0...999,9; error < 1% f.s. (t > 300°C)
U range -99,9...99,9 e -99...99°C; error < 0.5% f.s.
for other range; errore < 0.2% f.s. (t > -150°C)
G error < 0.2% f.s. (t > 300°C)
D error < 0.2% f.s. (t > 200°C)
C range 0...2300; error < 0.2% f.s.
for other range; error < 0.5% f.s.
NTC errore < 0.5% f.s.
Tc type J, K, E, N, L error < 0,2% f.s.
JPT100 e PTC
PT100 range -200...850°C accuracy at 25°C lower than
0,2% f.s.. In range 0...50°C:
• accuracy lower than 0,2% f.s. in range -200...400°C
• accuracy lower than 0,4% f.s. in range +400...850°C
(where f.s. is referred to range -200...850°C)
13
0 ... 63
IN PV AL4 AL3 AL2
5 4 3 2
1 1 0 0 0
0 ... 31
OUT4 OUT3 OUT2
4 3 2 1
1 0 0 1
User interface
0 ... 127
Virtual instrument
DISP LED LED LED LED
OUT4 OUT3 OUT2 OUT1
5 4 3 2 1
0 0 0 0 0
In case of custom linearization, test
limits for setting LO and HI errors
are given by the calibration values.
If these limits are not exceeded,
they are taken into consideration as
limits L.S and H.S.
N.B.: for the version R77 are not
available the probe codes 0...39,
48...51, 54...58
error < 0,2% f.s.
AL1
1 0
0
OUT1
0
1
0
1