Auto Scanning Function; Wind Speed And Direction; Weather Alarms - Oregon Scientific WMR968 Manual Del Usuario

AUTO SCANNING FUNCTION

The auto scanning function is available for the outdoor/
channel window for both the temperature and humidity.
To use it,
1. Press the outdoor/channel temperature or humidity
window.
2. Press and hold [ ] . The main unit will start scanning
from the active temperature and humidity display. Each
channel will be displayed for about 4 seconds.
To exit the auto scanning routine, press any window or
control button.
RAINFALL
The rate of rainfall can be displayed in mm/hr or in/hr.
To select the display unit,
1. Press the rainfall window.
2. Press [UNIT] for the desired setting.
To display yesterday's rainfall and the total rainfall from
the last cleared date,
1. Press the rainfall window.
2. Press [MEMORY] for the desired record. Yesterday's
rainfall will be displayed with "YESTERDAY" shown in
the rainfall window. Total rainfall will be displayed with
"TOTAL" shown in the rainfall window. The time and
date of the record will be displayed alternatively with
the "SINCE" icon in the clock window for total rainfall.
NOTE Yesterday's rainfall record will be updated when
the real time clock runs from 11:59:59 pm to 12:00:00 am.
And it is counted for 12:00:00 am of one day to 12:00:00
am on the next day.
If the rain sensor detects no rainfall for about two
consecutive hours, the current rate of rainfall will be
displayed as zero.
To clear the total rainfall,
1. Press the rainfall window.
2. Press and hold [MEMORY] until the key tone is heard.
Yesterday's rainfall record will not be affected when you
clear the total rainfall.

WIND SPEED AND DIRECTION

The current wind speed and direction are displayed in the
wind speed and direction window.
To display the average wind speed, press the window till
the "AVERAGE" icon is displayed.
The wind speed can be displayed in m/s, kph, mph or
knots.
To select the display unit,
1. Press the wind speed and direction window.
2. Press [UNIT] for the desired setting.
To display the maximum speed and direction for gust wind,
1. Press the wind speed and direction window.
2. Press [MEMORY]. The time and date of the record will
also be displayed aternatively with the "STAMP" icon in
the clock window.
To clear the record,
1. Press the wind speed and direction window.
2. Press and hold [MEMORY].
As for the wind direction, it is displayed in a digital compass
with bearing readouts.

WEATHER ALARMS

Weather alarms are used to alert you to certain weather
conditions. Once activated, the alarm will go off when a
certain set of criterion is met.
You can set alarms for:
- Indoor, outdoor and channel high temperatures
- Indoor, outdoor and channel low temperatures
- Indoor, outdoor and channel dew point approaching
- Indoor, outdoor and channel high humidity
- Indoor, outdoor and channel low humidity
- High rainfall rate
- Pressure drop
- High gust wind
- Low wind chill
To set a weather alarm,
1. Press the window containing the weather element you
want to set.
2. Press [ALARM]. The current alarm setting will be
displayed.
3. Press and hold [SET].
4. Press [ ] and [ ] for the desired setting.
5. Press [SET].
For temperatures and humidity, the high and low alarms
can be set in sequence. After entering the value for one
alarm, you will be prompted to enter the value for the
other.
A weather alarm is activated once set. When the set
criteria is met, an alarm will go off and the current reading
will flash together with the corresponding indicator.
If that happens in the outdoor/channel temperature or
humidity window, the "OUT" indicator will flash to show
that the criteria set for the outdoor thermo-hygrometer has
been met. If it is one of the separate sensors, the
[CHANNEL] indicator will flash. Press the window
repeatedly to locate the channel in question.
When a weather alarm goes off, press any button to stop
the alarm. The alarm is still active until you deactivate the
function or the criteria is no longer met.
To do so,
1. Press the window containing the weather element you
want to set.
2. Press [ALARM].
3. Press [ALARM ON/OFF] to deactivate the function.
To turn on the function again, simply follow the same
procedure and press [ALARM ON/OFF].
6