GM 23453669 Instrucciones De Montaje

Accessory Splash Guard Rear Kit
Please read instructions thoroughly before starting.
Tools Required
T15 Torx Screw Driver
Drill
3/16" (5.0 mm) Drill Bit
Clean Cloth/Rag
Package Contents
Description
Left Hand Splash Guard
Right Hand Splash Guard
M4.2 Screw without Washer
M4.2 Screw with Washer
U-nut
Instruction Sheet
Alcohol Wipe
Installation Procedure
1. Remove rear tire.
2. Clean and degrease body panel where splash guards are to
be located.
3. Remove screw from locations (A) and (B) of rear fascia as
shown in Fig. 1. Retain fasteners.
4. Align Splash Guard to vehicle and reinstall one existing screw
at location (B). Install one M4.2 Self-tapping Screw (without
washer) at location (A) as shown in Fig. 2 and Fig. 3.
5.
holes at locations (C) and (D) as shown in Fig. 2 and Fig. 3.
6. Remove fasteners and Splash Guard. Attach U-nut to bottom
of fascia as shown in Fig. 4.
7. Reinstall Splash Guard to vehicle and reinstall one existing
screw at location (B). Install one M4.2 Screw (without washer)
at location (A) as shown in Fig. 5.
8. Install one M4.2 Screw (with washer) at location (C) as shown
in Fig. 5. Install U-nut behind wheel liner to hold screw.
9. Install one M4.2 Screw (with washer) at location (D) as shown
in Fig. 6.
10. Pull splash guard forward slightly and remove tape liner as
shown in Fig 5. Apply 20-30 pounds of pressure along the
length of the tape to ensure proper contact.
11. On vehicles with dual exhaust - Repeat steps 1 through 10
on the opposite side of vehicle.
12. On vehicles with single exhaust
remove two fasteners at locations (E) and (F) as shown
in Fig 7. Carefully pull down on the closeout panel to gain
access behind the wheel liner. Repeat steps 1 through 10 on
passenger side. Put closeout panel back in place. Reinstall
fastener at location (E). Do NOT reinstall fastener at location
(F).
13. Guards can be cleaned with any commercially available
cleaner.
NOTE: Max torque on M4.2 Screw is 3.0 N m
Splash Guard - Rear
ALL INFORMATION WITHIN
DATE
ABOVE BORDER TO BE PRINTED
EXACTLY AS SHOWN ON 8.5 x 11
14AU15
WHITE 16 POUND NON-BOND
RECYCLABLE PAPER.
PRINT ON BOTH SIDES, EXCLUD-
ING TEMPLATES.
TO BE UNITIZED IN ACCORDANCE
WITH GM SPECIFICATIONS.
Quantity
1
1
2
4
4
1
1
REVISION
Initial Release - Vinay Saini
FIGURE 1
FIGURE 3
DRILL
HERE
VIEW
FROM
BELOW
FIGURE 5
U-NUT
(WITHOUT WASHER)
M4.2 SCREW
(WITH WASHER)
IR 14AU15
INSTALLATION INSTRUCTIONS
AUTH DR
TITLE
2285092
PART NO.
23453669
B
FIGURE 2
A
M4.2 SCREW
(WITHOUT WASHER)
DRILL
HERE
C
FIGURE 4
D
EXISTING
SCREW
TAPE
B
LINER
C A
M4.2 SCREW
M4.2 SCREW
(WITH WASHER)
FIGURE 7
F
23453669
PART NO.
Splash Guard - Rear
SHEET
B
A
D
FIGURE 6
VIEW
FROM
BELOW
D
E
CLOSEOUT
PANEL
1 3
SHEET OF
1 3
OF