Table I, Pipe Wall Thickness - RIDGID 918 Manual

Table I. Pipe Wall Thickness
NOTE: All Dimensions are in Inches.
CARBON STEEL OR
ALUMINUM PIPE OR TUBE
Pipe
Size
Wall Thickness
Schedule
Min.
1 5, 10, 40 0.065
1 1 / 5, 10, 40 0.065
4
1 1 / 5, 10, 40 0.065
2
2 5, 10, 40 0.065
2 1 / 5, 10, 40 0.083
2
3 5, 10, 40 0.083
3 1 / 5, 10, 40 0.083
2
4 5, 10, 40 0.083
5 5, 10, 40 0.109
6 5, 10, 40 0.109
8 5, 10, 40* 0.109
10 5, 10 0.134
12 5, 10 0.165
* Do not use to groove 8" schedule 40 steel pipe harder than 150 BHN.
Table II. Standard Roll Groove Specifications
NOTE: All Dimensions are in Inches.
PIPE
NOM.
DIAMETER
PIPE
SIZE O.D.
1 1.315
1 1 / 1.660
4
1 1 / 1.900
2
2 2.375
2 1 / 2.875
2
3 3.50
3 1 / 4.00
2
4 4.50
5 5.563
6 6.625
8 8.625
10 10.75
12 12.75
(1) As per AWWA C606-15
(2) Nominal Groove Depth is provided as a reference dimension only. Do not use groove depth to determine acceptability of a groove.
NOTE: Follow fitting manufacturer's recommendations regarding maximum allowable flare dimension.
999-998-946.10_REV. C
Schedule
Max.
0.133 5, 10
0.140 5, 10, 40
0.145 5, 10, 40
0.154 5, 10, 40
0.203 5, 10
0.216 5, 10
0.226 5, 10
0.237 5, 10
0.258 5, 10
0.280 5, 10
0.322 5, 10
0.165 5, 10
0.180 5, 10
T
MIN. GASKET
WALL
TOL. THK. +.015/-.030
+.013 0.065
-.013
+.016 0.065
-.016
+.019 0.065
-.019
+.024 0.065
-.016
+.029 0.083
-.016
+.035 0.083
-.031
+.040 0.083
-.031
+.045 0.083
.031
+.056 0.109
.031
+.063 0.109
-.031
+.063 0.109
-.031
+.063 0.134
-.031
+.063 0.156
-.031
STAINLESS STEEL
PIPE OR TUBE
Wall Thickness
Min. Max.
0.065 0.109
0.065 0.140
0.065 0.145
0.065 0.154
0.083 0.188
0.083 0.188
0.083 0.188
0.083 0.188
0.109 0.188
0.109 0.188
0.109 0.148
0.134 0.165
0.165 0.180
(1)
A B
GROOVE
SEAT WIDTH
+.030/-.015
0.625 0.281
0.625 0.281
0.625 0.281
0.625 0.344
0.625 0.344
0.625 0.344
0.625 0.344
0.625 0.344
0.625 0.344
0.625 0.344
0.750 0.469
0.750 0.469
0.750 0.469
918 Roll Groover
PVC PIPE
Wall Thickness
Schedule
Min.
40 0.133
40 0.140
40, 80 0.145
40, 80 0.154
40, 80 0.203
40, 80 0.216
40 0.226
40 0.237
40 0.258
40 0.280
40 0.322
— —
— —
Figure 30
C
GROOVE DIAMETER
O.D. TOL.
1.190 +.000
1.535 +.000
-.015
1.535 +.000
-.015
2.250 +.000
-.015
2.720 +.000
-.015
3.344 +.000
-.015
3.834 +.000
-.020
4.334 +.000
-.015
5.395 +.000
-.015
6.455 +.000
-.015
8.441 +.000
-.020
10.562 +.000
-.025
12.531 +.000
-.025
Max.
0.133
0.140
0.200
0.218
0.276
0.300
0.226
0.237
0.258
0.280
0.322
—
—
D
NOM.
GROOVE
DEPTH
(2)
0.063
0.063
0.063
0.063
0.078
0.078
0.083
0.083
0.084
0.085
0.092
0.094
0.110
21