Gorenje DK2000P2 Montaje Y Modo De Empleo página 8

INSTRUCTION ON MOUNTING AND USE
GB
• Montage - Fig. 3
Open the steam screen and remove the grease filter.
Install the carbon filter on the back of the grease filter and
fix with two rods.
Attention! The rods are included in the carbon filter
packing and not on the hood.
• To dismantle the filter act in the reverse manner.
Replacing lamps - Fig. 4
Firstly check that the lamps are well cooled prior to replacing
them.
Extract the lamp cover by levering it off with a small
screwdriver or similar tool.
Replace the damaged light bulb.
Only use halogen bulbs of 20W max (G4), making sure you
do not touch them with your hands.
Close the lamp cover (it will snap shut).
If the lights do not work, make sure that the lamps are
fitted properly into their housings before you call for
technical assistance.
Caution
This appliance is designed to be operated by adults. Children
should not be allowed to tamper with the controls or play with
the appliance.
Do not use the cooker hood where the grill is not correctly
fixed! The suctioned air must not be conveyed in the same
channel used for fumes discharged by appliances powered
by other than electricity. The environment must always be
adequately aerated when the cooker hood and other
appliances powered by other than electricity are used at the
same time. Flambé cooking with a cooker hood is
prohibited. The use of a free flame is damaging to the filters
and may cause fire accidents, therefore free flame cooking
must be avoided. Frying of foods must be kept under close
control in order to avoid overheated oil catching fire. Carry
out fumes discharging in accordance with the regulations in
force by local laws for safety and technical restrictions.
Installation - Fig. 5
Consult the designs in the front pages referenced in the text
by alphabet letters. Closely follow the instructions set
out in this manual. All responsibility, for any eventual
inconveniences, damages or fires caused by not complying
with the instructions in this manual, is declined.
The minimum distance between the supporting surface for
the cooking vessels on the hob and the lowest part of the
range hood must be not less than 40cm from electric cookers
and 65cm from gas or mixed cookers.
If the instructions for installation for the gas hob specify a
greater distance, this has to be taken into account.
The hood is supplied in SUCTION version.
It is necessary to have an evacuation conduit going from the
upper B exit to the extraction hole towards the exterior.
In this case a connection ring (12A) has to be installed on
the B extraction hole.
Il you intend using the hood in the FILTERING version,
fumes and steam are recycled through the F deflector (12F).
It is possible to use the other deflector C supplied (12G): in
this case you must connect it to the extraction hole B with
an evacuation conduit.
Preliminary information for installation of the hood
Expansion wall plugs are provided to secure the hood to most
types of walls/ceilings. However, a qualified technician must
verify suitability of the materials in accordance with the type of
wall/ceiling. The wall/ceiling must be strong enough to take the
weight of the hood.
Do not tile, grout or silicone this appliance to the wall.
Surface mounting only.
For the filtering version chimney may be installed or not
according your needs.
During electrical connection ensure the power supply is
disconnected at the domestic main switch.
• Apply three adhesive strips C to the back of the hood.
• Trace a centre line on the wall to facilitate the montage
(1), position the hole template so that the middle line
printed on it corresponds to the centre line previously
drawn and that the lower side of the grill corresponds to
the lower part of the hood once mounted (2).
• Make two holes with the 8 mm Ø drill and fix the support
bracket with two dowels and wall screws (3).
• Open the steam screen and remove the grease filter (see
relative paragraph).
Fix the chimney bracket with two dowels and wall
screws (4).
• Hang up the hood (5), adjusting its position (6-7) and from
the inner part of the hood mark two points for the definitive
fixing. Remove the hood and make two 8 mm Ø holes
(9), insert two wall dowels, hang the hood up again and
fix it definitively with two screws (10).
• Connect the electricity (11), but leave the hood
disconnected from the general electric panel of the
house.
9