Optional Accessories - DeWalt DWS778 Traducido De Las Instrucciones Originales

english
1. Set your saw to the prescribed angles and make a few trial
cuts.
2. Practice fitting the cut pieces together.
Example: To make a four-sided box with 25° exterior angles
(angle "A") (Fig. 21), use the upper right arc. Find 25° on
the arc scale. Follow the horizontal intersecting line to either
side to get the mitre angle setting on the saw (23°). Likewise
follow the vertical intersecting line to the top or bottom to get
the bevel angle setting on the saw (40°). Always try cuts on a
few scrap pieces of wood
to verify the settings on the saw.
WARNING: Never exceed the compound mitre limits
of 45° bevel with 45° left or right mitre.
`
Dust Extraction (Fig. 1, 3, 4)
WARNING: Whenever possible, connect a dust
extraction device designed in accordance with the
relevant regulations regarding dust emission.
Connect a dust collection device designed in accordance with
the relevant regulations. The air velocity of externally connected
systems shall be 20 m/s +/- 2 m/s. Velocity to be measured
in the connection tube at the point of connection, with the tool
connected but not running.
NOTE: The DWV9000 twist-lock quick connector (II) is
recommended as an optional accessory to connect to the dust
extraction device.
Transporting (Fig. 1, 2)
WARNING: In order to conveniently carry the mitre
saw, the base is provided with two hand indentations
(DD). Never use guards to lift or transport the mitre
saw.
1. To transport the saw, set the bevel and mitre positions to 0°.
2. Press the lower guard lock-up release lever (B) (Fig.1).
3. Press the saw head down and push in the lock-down button
(W) (Fig. 2).
4. Bring the saw head to rest position and tighten the traverse
lock (S).
MAINTENANCE
Your D WALT power tool has been designed to operate over a
e
long period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and regular
cleaning.
WARNING: To reduce the risk of injury, turn unit
off and disconnect machine from power source
before installing and removing accessories,
before adjusting or changing set-ups or when
making repairs. Be sure the trigger switch is in the
OFF position. An accidental
start-up can cause injury.
WARNING: If the saw blade is worn, replace it with a
new sharp blade.
Lubrication
Your power tool requires no additional lubrication.
34
Cleaning
Before use, carefully check the upper blade guard, movable lower
blade guard as well as the dust extraction tube to determine
that it will operate properly. Ensure that chips, dust or workpiece
particle cannot lead to blockage of one of the functions.
In case of workpiece fragments jammed between saw blade and
guards disconnect the machine from the power supply and follow
the instructions given in section Mounting the Saw Blade.
Remove the jammed parts and reassembling the saw blade.
WARNING: Blow dirt and dust out of the main
housing with dry air as often as dirt is seen collecting
in and around the air vents. Wear approved eye
protection and approved dust mask when performing
this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of the
tool. These chemicals may weaken the materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside
the tool; never immerse any part of the tool into a
liquid.
WARNING: To reduce the risk of injury, regularly
clean the table top.
WARNING: To reduce the risk of injury, regularly
clean the dust collection system.

Optional Accessories

WARNING: Since accessories, other than those
offered by D WALT, have not been tested with this
e
product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
D WALT, recommended accessories should be used
e
with this product.
SUPPORT FOR LONG PIECES (FIG. 5)
• Always support long pieces.
• For best results, use the extension work support (DE7023) to
extend the table width of your saw (available from your dealer
as an option). Support long workpieces using any convenient
means such as saw-horses or similar devices to keep the
ends from dropping.
RANGE OF SAW BLADES AVAILABLE (RECOMMENDED BLADES)
Type of blade Blade dimensions
DT1158 series 30 250 mm
DT4282 series 40 250 mm
DT4226 series 40 250 mm
DT4287 series 40 250 mm
DT4282 series 40 250 mm
Consult your dealer for further information on the appropriate
accessories.
Usage
For general purpose, ripping and
cross-cutting of wood and
plastics
TCG for use with aluminum
ATB for fine cutting of
manmade and natural wood
TCG for extra fine cutting of
manmade and natural wood
Aluminium cutting