Stanley FATMAX SFMCE530 Traducido De Las Instrucciones Originales página 11

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 56
Fully Charged:
Green LED Solid
Hot/Cold Pack Delay:
Green LED Intermittent
Red LED Solid
Note: The compatible charger(s) will not charge a faulty
battery pack. The charger will indicate a faulty battery pack by
refusing to light.
Note: This could also mean a problem with a charger. If the
charger indicates a problem, take the charger and battery
pack to be tested at an authorized service centre.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indefinitely. The charger will keep the battery
pack fresh and fully charged.
Hot/Cold Pack Delay
When the charger detects a battery that is too hot or too cold,
it automatically starts a Hot/Cold Pack Delay, the green LED
(7a) will flash intermittently, while the red LED (7b) will remain
on continuously, suspending charging until the battery has
reached an appropriate temperature. The charger then
automatically switches to the pack charging mode. This
feature ensures maximum battery life.
Battery state of charge indicator (Fig. B)
The battery includes a state of charge indicator to quickly
determine the extent of battery life as shown in figure B. By
pressing the state of charge button (6a) you can easily view
the charge remaining in the battery as illustrated in figure B.
Installing and Removing the Battery Pack (Not
Supplied) from the tool
To install battery pack (Fig. C)
Insert battery pack (6) firmly into tool until an audible click
u
is heard as shown in figure C. Ensure battery pack is fully
seated and fully latched into position.
To remove battery pack (Fig. D)
Depress the battery release button (6b) as shown in figure
u
D and pull battery pack (6) out of tool.
(Original instructions)
Prior to Operation
Warning! Make sure the nozzle always points away
from you and any bystanders.
Warning! DO NOT drop anything into the nozzle.
Warning! DO NOT exceed 60 minutes "ON" in a
2 hour period.
Switching on and off (Fig. E, F)
To power on the tool, flip lock-off (5) upwards and
u
depress the trigger (1).
To turn the unit off release the trigger.
u
Note: Disconnect the tool from the power source and let
the tool cool down before moving or storing it.
Correct hand position (Fig. F)
Warning! To reduce the risk of serious personal
injury, ALWAYS use proper hand position as shown.
Warning! To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
handle as illustrated in figure F.
Cool down period (Fig. G)
The nozzle and accessory becomes very hot during use.
Turn heat gun off, disconnect from the power source, place
in position shown in Fig.G, and let the tool cool down for at
least 30 minutes before moving or storing it.
Removing paint
Warning! Refer to Important Notice under Additional Safety
Information before using the tool to remove paint.
Warning! Do not strip metal window frames as the
heat may crack the glass.
When striping other window frames, use a glass protection
u
nozzle.
To prevent igniting the surface, do not keep the
u
tool directed at one spot too long.
Avoid collecting paint on the scraper accessory, as
u
it may ignite. If necessary, carefully remove paint
debris from the scraper accessory using a knife.
Attach the appropriate accessory.
u
To power on the tool, flip lock-off (5) upwards and depress
u
the trigger 1 .
Direct the hot air onto the paint to be removed.
u
Best results will be achieved if the heat gun is moved
slowly, but CONSTANTLY, from side to side to evenly
distribute heat. DO NOT LINGER OR PAUSE IN ONE
SPOT.
When the paint softens, scrape the paint away using a
u
hand scraper.
ENGLISH
11

Publicidad

Tabla de contenido
loading

Tabla de contenido