Fein MShy649-1 Manual Del Usuario página 21

OBJ_BUCH-0000000036-001.book Page 21 Tuesday, July 5, 2011 9:14 AM
Identify additional safety measures to protect the opera-
tor from the effects of vibration such as: maintain the tool
and the accessories, keep the hands warm, organisation
of work patterns.
The vibrational emission values are given for dry grinding
of metal with grinding points. Other applications, such as
shaping with hard metal cutters, can lead to other vibra-
tional emission values.
Handling hazardous dusts
For work procedures with this power tool where mate-
rial is removed, dusts develop that can be hazardous to
one's health.
Contact with or inhaling some dust types, e. g. asbestos
and asbestos-containing materials, lead-containing coat-
ings, metal, some wood types, minerals, silicate particles
from materials containing stone, paint solvents, wood
preservatives, antifouling paints for vessels, can trigger
allergic reactions to the operator or bystanders and/or
lead to respiratory infections, cancer, birth defects or
other reproductive harm. The risk from inhaling dusts
depends on the exposition. Use dust extraction matched
appropriately for the developing dust, as well as personal
protective equipment and provide for good ventilation of
the workplace. Leave the processing of asbestos-contain-
ing materials to specialists.
Wood and light-metal dust, hot mixtures of sanding dust
and chemical materials can self-ignite under unfavourable
conditions or cause an explosion. Avoid sparking in the
direction of the dust collector as well as overheating of
the power tool and the materials being sanded, empty the
dust collector/container in time, observe the material
manufacturer's working instructions, as well as the rele-
vant regulations in your country for the materials being
worked.
Operating instructions.
Take care that the inner flange is mounted firmly on the
output spindle and that the centering sleeve is mounted.
Make sure to check that the grinding accessory is wider
than the height of the centering sleeve. Pay attention that
the grinding accessory is properly centered between the
inner flange and the threaded flange.
Move the power tool back and forth applying uniform
pressure, so that the work piece surface does not
become too hot.
Motor protection switch (MShy664-1)
(see page 6).
If given, the motor protection switch switches off the
power tool in case of overload. After approx. 30 seconds
upon actuation, the electronic system can be reset via
button (a).
Do not actuate button (a) until after having released the
power tool's switch.
Repair and customer service.
When working metal under extreme operat-
ing conditions, it is possible for conductive
dust to settle in the interior of the power tool.
The total insulation of the power tool can be impaired.
Blow out the interior of the power tool via the ventila-
tion slots frequently with dry and oil-free compressed air,
and connect a residual current device (RCD) on the line
side.
If the supply cord of this power tool is damaged, it must
be replaced by a specially prepared cord available through
the FEIN customer service centre.
If required, you can change the following parts yourself:
Threaded flange, inner flange, centering sleeve, applica-
tion tools
Warranty and liability.
The warranty for the product is valid in accordance with
the legal regulations in the country where it is marketed.
In addition, FEIN also provides a guarantee in accordance
with the FEIN manufacturer's warranty declaration.
The delivery scope of your power tool may include only
a part of the accessories described or shown in this
instruction manual.
Declaration of conformity.
FEIN declares itself solely responsible for this product
conforming with the relevant provisions given on the last
page of this Instruction Manual.
Technical documents at: C. & E. FEIN GmbH, EGZ,
D-73529 Schwäbisch Gmünd
Environmental protection, disposal.
Packaging, worn out power tools and accessories should
be sorted for environmental-friendly recycling.
Selection of accessories
(see pages 11 – 12).
Use only original FEIN accessories. The accessories must
be intended for the power tool type.
A Wheel guard
B Inner flange
C Holding rod
D Centering sleeve
E Double-sided conical grinding disc
F Abrasive fleece wheel
G Threaded flange
H Small contact belt sander, sanding width 50 mm
I Contact disc, 50 mm
J Linen sanding belt, 50 mm width
K Small contact belt sander, sanding width 30 mm
L Special inner flange for small contact belt sander with
30 mm sanding width
M Contact disc, 30 mm
N Special outer flange for small contact belt sander with
30 mm sanding width
O Hexagon nut
P Linen sanding belt, 30 mm width
en
21