Makita VC002GL Manual De Usuario página 16

Installing powder filter (HEPA) and
prefilter (for dry dust)
CAUTION:
Never pick up water or other liquids
or wet dusts when using the powder filter. Picking up
such things may cause the powder filter breakage.
To use powder filter:
1. Place the prefilter into the tank aligning the mount-
ing position markings on the prefilter and tank.
2.
Set the damper into the prefilter, and then place
the powder filter over the damper aligning the mounting
position markings on the powder filter and prefilter.
3. Mount the head unit over the tank and secure
them with the locking latches.
► Fig.11: 1. Head unit 2. Powder filter (HEPA) 3. Damper
4. Prefilter 5. Tank 6. Mounting position marking
NOTICE:
Before using the powder filter, make
sure that prefilter and damper are used together. It
is not allowed to install powder filter alone.
Installing paper pack
Optional accessory
WARNING:
Before using a paper pack, make
sure that the prefilter is used together. Failure to
use the prefilter together may cause unusual noise
and heat, resulting in a fire.
NOTICE:
Never pick up water or other liquids
or wet dusts when using a paper pack. Picking up
such things may cause the paper pack breakage.
NOTICE:
Before using a paper pack, make sure that the
powder filter, damper and prefilter are always used together.
1. Unfold a paper pack.
2. Align the paper pack opening with the dust intake of the tank.
3. Install the paper pack into the tank with its card-
board opening hooked on the paper pack holder.
► Fig.12: 1. Paper pack 2. Cardboard opening
3. Paper pack holder 4. Dust intake
Installing polyethylene bag
With a polyethylene bag installed in the tank, you can
easily empty the tank without letting your hands dirty.
Lay a polyethylene bag over the tank, and slip one side
of the top edge of the bag at its open end in between
the holder plate and the front wall of the tank.
► Fig.13: 1. Holder plate 2. Front wall of tank
3. Polyethylene bag
Spread the other top edges of the bag outwards over
the top rims of the tank. Place the prefilter over the poly-
ethylene bag to fasten the opening of the bag securely.
► Fig.14: 1. Prefilter
NOTE: A polyethylene bag available on the market can
be used. 0.04 mm or thicker one is recommended.
NOTE: Too much dust will tear the bag easily, so do not
collect the dust more than the half of the bag capacity.
Emptying tank with polyethylene bag
WARNING:
is switched off and the battery cartridges are
removed before emptying the tank. Failure to do
so may cause an electric shock and serious personal
injury.
NOTICE:
Do not apply a great impact on the
tank. Applying a great impact may cause deformation
and damage to the parts.
NOTICE:
Empty the tank at least once a day
although this depends on picked-up dust volume
in the tank. Or, the suction force will weaken and the
motor may be broken.
NOTICE:
Do not grab the hooks or latches when
emptying the tank. Grabbing the hooks or latches
may cause them to break.
Release the locking latches and lift the head unit up off
the tank.
Shake off dust from the prefilter before lifting the filter
away from the tank.
Then remove the polyethylene bag out of the tank,
closing the opening of the bag by hand.
► Fig.15: 1. Polyethylene bag 2. Tank
NOTE: Take the polyethylene bag out of the tank
carefully to avoid it from being scratched and torn by
the edges inside the tank.
NOTE: Empty the polyethylene bag before it
becomes full. Too much dust in the tank may cause
the polyethylene bag to be torn.
Installing multi hook
Use the multi hook to hold a hose, accessories and
attachments not in use in place, and you can quickly
take them out according to your preferences.
► Fig.16
Place the multi hook over the mounting base at the rear
of the cleaner, setting the rails on the multi hook along
the grooves on the mounting base.
► Fig.17: 1. Multi hook 2. Mounting base
Installing MAKPAC adapter
Optional accessory
Connectable and stackable MAKPAC storage cases
can be installed on top of the cleaner with an optional
adapter. The cases are available in many sizes and
styles to suit your preferences.
Place the mounting base hook over the handle of the
cleaner with its mounting surface facing upwards when
the handle is folded into the closed position.
► Fig.18: 1. Mounting base hook 2. Mounting surface
3. Handle
Mount the MAKPAC adapter onto the mounting base
hook, and secure them together with four screws
provided.
► Fig.19: 1. MAKPAC adapter 2. Mounting base hook
3. Screw
16 ENGLISH
Always make sure that the cleaner