EINHELL TC-MS 2513 L Manual De Instrucciones página 36

Sierra ingletadora
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

equipment. Never use the guards for handling
or moving the equipment.
Use the saw only if the guards are correctly
positioned and only if the saw is in perfect
condition and has been properly serviced.
When cutting miters, make sure that the
device for swiveling the arm is fastened se-
curely.
The floor around the machine must be level,
clean and free of loose particles, such as
chips and cutting residues.
Make sure the workplace and the room are
sufficiently illuminated.
The operator must receive proper training
in the use, adjustment and operation of the
machine.
Use only properly sharpened saw blades
Check that the speed indicated on the saw
blade is at least as high as the speed indica-
ted on the saw.
Be sure to use only spacers and spindle rings
which are specified by the manufacturer as
suitable for the intended purpose.
If the machine is equipped with a laser, this
laser may not be replaced by a different type
of laser. Repairs may only be carried out by
the manufacturer of the laser or one of his
authorized agents.
Do not remove any cutting residues or other
parts of workpieces from the cutting zone
while the machine is running and not before
the saw unit is at rest.
Make sure that the machine is always secu-
red on a workbench or a table. Use the holes
in the machine's base frame to secure the
machine. Bolt the base frame to a workbench
or a table.
Support long workpieces (e.g. with a roller
table) to prevent them sagging at the end of
a cut.
To make cuts correctly and safely:
- Always clamp the workpiece securely to the
saw table
- Each time before making a cut, make sure
that the machine stands securely
4. Additional safety instructions
Always pull the plug out of the power socket
before adjusting or servicing the machine.
Give these safety instructions to all persons
who work on the machine.
Do not use this saw to cut fire wood.
Caution! Hands and fingers may be injured on
the rotating saw blade.
Before you use the machine for the first time,
Anl_TC_SM_2513_L_SPK8.indb 36
Anl_TC_SM_2513_L_SPK8.indb 36
GB
check that the voltage marked on the rating
plate is the same as your supply voltage.
If you need to use an extension cable, make
sure its conductor cross-section is big
enough for the saw's power consumption.
Minimum cross-section: 1.5 mm².
If you use a cable reel, the complete cable
must be pulled off the reel.
Do not carry the saw by its power cable.
Operators have to be at least 18 years of age.
Trainees of at least 16 years of age are allo-
wed to use the machine under supervision.
Keep children away from the machine when it
is connected to the power supply.
Check the power cable. Never use a faulty or
damaged power cable.
Keep your workplace clean of wood scrap
and any unnecessary objects.
Persons working on the machine should not
be distracted.
After you have switched off the motor, never
slow down the saw blade by applying pressu-
re to its side.
Only fit blades which are well sharpened and
have no cracks or deformations.
Faulty saw blades must be replaced imme-
diately.
Never use saw blades which do not comply
with the data specified in this manual.
Note the direction of rotation of the motor and
saw blade.
It is imperative to make sure that the arrow
(direction of rotation) on the saw blade con-
forms with the arrow on the machine.
Pull out the power plug and twist the blade
with your hand into the 45° and 90° positions
in order to make sure that the blade does not
touch the turntable in any position. If necessa-
ry, readjust the saw head.
It is imperative to make sure that all devices
which cover the saw blade are in good wor-
king order.
Never wedge the hinged guard hood in open
position.
Never dismantle the machine's safety devices
or render them inoperative.
Never cut workpieces which are too small to
clamp securely on the saw table.
Avoid placing your hands in hazardous posi-
tions in which one or both hands could touch
the saw blade if they slip suddenly.
There must be no nails or other foreign bo-
dies in the workpiece.
Always stand to the side of the saw blade
when working with the saw.
- 36 -
15.10.15 09:50
15.10.15 09:50

Publicidad

Capítulos

Tabla de contenido
loading

Tabla de contenido