Operation - EINHELL TC-MS 2513 L Manual De Instrucciones

Sierra ingletadora
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Undo the tightening screw (12) and use the
handle (2) to tilt the machine head (4) to the
left until it coincides at 45°.
Place the 45° stop angle (a) between the saw
blade (5) and the rotary table (8).
Slacken the counter nut (25) and adjust the
setting screw (26) until the angle between the
saw (5) and the rotary table (8) equals exactly
45°.

6. Operation

6.1 90° cross-cuts and 0° rotary table (Fig. 1)
Press the main switch (3) to turn on the saw.
Important! Place the material you want to saw
flat on the machine surface and secure with
the
clamping device (19) so that the mate-
rial cannot move while you are cutting.
After switching on the saw, wait for the blade
(5) to reach its maximum speed.
Press the release lever (1) sideways and,
using the handle (2), apply steady and light
downward pressure to move the machine
head through the workpiece.
When the cut is completed, return the ma-
chine to its top parking position and let go of
the On/Off switch. Caution! A return spring
causes the machine head to rise automati-
cally at the end of the cut. Do not let go of the
handle (2) as soon as the cut is completed
but steady the machine head and allow it to
rise slowly.
6.2 90° cross-cuts and 0°-45° rotary table
(Fig.6)
The crosscut saw can be used to make right and
left angular cuts of 0°- 45° in relation to the stop
rail.
Lift the machine head (4) to its top position.
Release the rotary table (8) by slackening the
locking handle (10) and pressing the latch
(11).
Turn the rotary table (8) by its handle (2) to
the angle you want, i.e. the mark (a) on the
rotary table has to comply with the required
angle dimension (17) on the base plate (9).
Re-tighten the locking handle (10) in order to
fix the rotary table (8) in position.
Make the cut as described in Section 6.1.
6.3 Mitre cuts 0°-45° and rotary table 0°
(Fig. 4/7)
The crosscut saw can be used to make miter cuts
Anl_TC_SM_2513_L_SPK8.indb 40
Anl_TC_SM_2513_L_SPK8.indb 40
GB
of 0° - 45° in relation to the work face.
Lift the machine head (4) to its top position.
Fix the rotary table (8) in 0° position.
Undo the tightening screw (12) and use the
handle (2) to tilt the machine head (4) to the
left until the pointer (a) coincides with the re-
quired angle value (15).
Re-tighten the locking nut (12) and make the
cut as described in Section 6.1.
6.4 Mitre cuts 0°-45° and rotary table 0°-45°
(Fig. 10)
The crosscut saw can be used to make miter cuts
to the left of 0°- 45° in relation to the work face
and, at the same time, 0° - 45° in relation to the
stop rail (double miter cut).
Lift the machine head (4) to its top position.
Undo the rotary table (8) by slackening the lo-
cking handle (10) and pressing the latch (11).
Adjust the rotary table (8) by its handle (2) to
the required angle (see also Section 6.2).
Retighten the tightening screw (10) in order to
secure the turntable in place.
Undo the tightening screw (12) and use the
handle (2) to tilt the machine head (4) to the
left until it coincides with the required angle
value (in this connection see also section
6.3).
Screw the tightening screw (12) back down
again.
Make the cut as described in Section 6.1).
6.5 Sawdust bag (Fig. 2)
The saw is equipped with a debris bag (14) for
sawdust and chips.
The debris bag (14) can be emptied by means of
a zipper at the bottom.
6.6 Replacing the saw blade (Fig. 11-14)
Before changing the saw blade: Remove the
power plug!
Wear work gloves to prevent injury when
changing the saw blade.
Swing the machine head upwards (4).
Undo the screw (z) on the cover plate (f) of
the saw blade.
Pull back the adjustable blade guard (6) and
at the same time turn the cover plate to achie-
ve access to the flange bolt.
Press the saw shaft lock (35) with one hand
while positioning the Allen key (d) on the
flange bolt (31) with the other hand. The saw
shaft lock (35) engages after no more than
one rotation.
Now, using a little more force, slacken the
- 40 -
15.10.15 09:50
15.10.15 09:50

Publicidad

Capítulos

Tabla de contenido
loading

Tabla de contenido