Tsc Quick Washing; Cleaning Tsc; Timer; Periodical Maintenance - Rancilio classe 10 Uso Y Manutención

Immerse the silicone pipe into a clean water bowl
for rinsing. Replace the water of the bowl where the
lance is immersed with cold clean water.
By pressing "enter" the display will show
RINSE RUNNING"
and no.2 cycles will start as follows:
- steam dispensing start for 40 sec.
- pause for 2 sec.
Keeping ''esc'' pressed for 2 seconds, during the
washing cycle the current phase is stopped and the
next phase will take place.
It is advisable to always complete the rinsing cycle
to remove any detergent residues.
Rinsing phases cannot be avoided.
In any case the TSC washing can be enabled whene-
ver necessary according to the previously described
procedure.
If during the washing cycle the water where the lance
has been immersed exceeds 80°C, the message
below will be displayed
temperature
too high
and the current cycle will be interrupted.
In this case replace the water where the lance is
immersed with at least half litre of cold water and
press "enter" to continue the washing cycle.

10.2.3. TSC quick washing

If enabled, at the programmed interval the display will
show the message to carry out TSC quick washing
and both leds of TSC keys will flash.
Press one of the two keys to carry out quick washing
(steam dispensing for approx. 3 sec.)
10.2.4. Cleaning TSC (Fig.13)
● Clean the TSC nozzle frequently with a sponge or
damp cloth. Make sure to clean the lower parts.
● Periodically use the cleaning tool included to clean
the TSC air pipe.
After this operation, push "Latte" button for 2-3
seconds.

10.2.5. Timer

The Timer buttons are used to exclude the timed
switching ON and OFF of the machine.
When the timer function is selected, if the machine
is OFF, press the "Esc" buttons on the programming
keypad (for at least 3 second) to switch the machine
ON; the machine remains ON until the next timed
switching OFF or until you press the same controls
again (for at least 3 seconds).
When the timer function is selected, if the machine
is ON, press the "Esc" buttons on the programming
keypad (for at least 3 second) to switch the machine
OFF; the machine remains OFF until the next timed
switching ON or until you press the same controls
again (for at least 3 seconds).
78
All manuals and user guides at all-guides.com

10.3. Periodical maintenance

Have been fitted with economizers which do not
draw water from the boiler to make hot water, the
water in the boiler need only to be renewed from
time to time.
10.3.1. Renewal of water in the boiler
To be carried out only by qualified personnel.
● Turn off the machine and wait for the pressure in
the boiler to diminish (gauge needl on "0").
● Insert a rubber hose into the hose-end fitting (3)
(Fig.14)
● Use the wrench (1) to immobilize the fitting (2) and
loosen the hose-end fitting (3).
● Allow the water to flow out completely; then, close
the fitting (3) and remove the rubber hose.
● Refill the boiler (paragraph 7.3.).

11. STOPPING THE MACHINE

A - Temporary stop
● Carry out cleaning and maintenance operations.
● Wind up the cable and fasten it to the machine
with sticky tape.
● Cover the machine and place it in a dry room. Do
not leave it exposed to atmospheric agents and
do not allow it to be touched by children or unift
persons.
To disconnect from the main power supply, consult
qualified personnel.
B - Definitive stop
● Besides carrying out the operations necessary for
a temporary stop, cut off the cable, pack the ma-
chine in cardboard, polystyrene or other packing
material and consign it to firms authorized for its
disposal or to second-hand goods dealers.

12. PROBLEMS AND REMEDIES

Check operations to be carried out by the
user with the plug disconnected.
For any type of problem or inconvenience not
specifically indicated, disconnect the plug and
contact our service centre without attempting
any direct repairs.
A) The machine does not start:
- check that the plug is connected;
- In case of power failure wait for the power to return
and check if the earth leakage protection circuit
breaker or the main switch is on;
- check the condition of the plug and the supply
cable; if damaged have them replaced by qualified
personnel.
B) There is water under the machine:
- check that the drainage tray is not obstructed.
C) Slow dispensing:
- check that the filters and delivery heads are clean;
- check that the coffee is not too finely ground.
D) Irregular steam delivery:
- check that the nozzles are not obstructed.