Operation; Controls - Rancilio classe 10 Uso Y Manutención

7. OPERATION

7.1. Controls (Fig.8)
1 Main switch
Two-position switch with led.
Turn on the switch (led on) the machine is turned
(apart from the boiler) and the pump is turned on
to fill the boiler;
2 Boiler resistance switch
Two-position switch with led.
On activating the switch (the led comes on) and
power is supplied to the resistance for the boiler
water.
3 Coffee dispensing switch (mod.S)
Two-position switch:
With switch ON, coffee is dispensed;
With switch OFF, dispensing of coffee is interrup-
ted.
4 Dispenser control lever (mod.RE)
Move the lever downward to start dispensing cof-
fee.
To stop dispensing, move the lever upward.
5 Coffee Dispensing Electronic Panel (mod. SDE)
This panel features 5 buttons for each dispenser
(max 4) and 5 LEDs consisting of the following:
4 (A-B-C-D) buttons for start/stop dispensing the
programmed coffee dose
1 (E) button for:
- Stop dispensing any dose
- Start in continuous mode
- Initialize dose programming for self-learning if
pressed for about 8 sec.(If the function is ena-
bled)
Each time a coffee is dispensed, the LED of the
relative button lights up.
During dose programming, the LED of the 5
flashes rapidly.
If the dose is supplied irregularly or the volumetric
counter is malfunctioning, the LED of the pressed
button flashes dispensing the dose on a time basis.
6 Hot Water and Cup-Warmer Panel (mod.S-RE)
6.1 Cup-warmer switch with two positions:
With switch ON, the LED flashes and the cup
warmer resistance is energized.
With switch OFF, the LED switches off and the
resistance is de-energized.
6.2 Two-position hot water switch (thermoregula-
ted):
With switch ON, the LED flashes and thermore-
gulated hot water is dispensed.
With switch OFF, the LED switches off and dispen-
sing stops.
All manuals and user guides at all-guides.com
th
button
6.3 Hot water switch (picking up directly from the
boiler) with two positions:
With switch ON, the LED flashes and hot water is
dispensed directly from the boiler.
With switch OFF, the LED switches off and dispen-
sing stops.
7 Hot Water and Function Panel (mod.SDE)
This panel features 5 buttons and 5 LEDs consi-
sting of the following:
1 cup-warmer button (7.1)
2 buttons for dispensing hot water (7.2 - 7.3)
1 steam-dispensing button with temperature
control (7.4)
1 steam delivery with temperature and emulsion
control (7.5)
7.1 The Cup Warmer
When the button is pressed, the display shows
the set power status of the resistance, which can
be of four types (off – minimum – medium – ma-
ximum).
If the button is pressed again within 2 seconds,
the set power status of the resistance moves to
the next step.
When the cup-warmer resistance is active (min,
med, or max status), the relative LED lights up.
7.2 When the button is pressed, thermoregulated wa-
ter is dispensed for the set time or until the button
is pressed again. During this type of dispensing,
the pump is switched ON.
7.3 When the button is pressed, hot water is dispen-
sed directly from the boiler for the set time or until
the button is pressed again.
If you press the 2 buttons for 2 seconds, dispensing
is continuous and only stops when the button is
pressed again.
Dispensing is discontinued automatically after 30
and 60 seconds, respectively.
7.4 Steam TSC (Optional)
When the button is pressed, the steam dispensing
solenoid valve is excited until the set temperature
is reached or until the button is pressed again.
69