Important Remarks; Conformity To Regulations - V2 KIT ECOGOLD230 Manual De Instrucciones

IMPORTANT REMARKS

For any installation problems please contact
V2 ELETTRONICA TEL. (+39) 01 72 81 24 11
V2 ELETTRONICA has the right to modify the product
without previous notice; it also declines any responsi-
bility to damage or injury to people or things caused
by improper use or wrong installation.
Please read this instruction manual very carefully
before installing and programming your control unit.
• This instruction manual is only for qualified
technicians, who specialize in installations and
automations.
• The contents of this instruction manual do not
concern the end user.
• Every programming and/or every maintenance
service should be done only by qualified technicians.
AUTOMATION MUST BE IMPLEMENTED IN COMPLIAN-
CE WITH THE EUROPEAN REGULATIONS IN FORCE:
EN 60204–1 (Machinery safety. electrical equipment of
machines, part 1: general rules)
EN 12445 (Safe use of automated locking devices,
test methods)
EN 12453 (Safe use of automated locking devices,
requirements)
• The installer must provide for a device
(es. magnetotermical switch) ensuring the omnipolar
sectioning of the equipment from the power supply.
The standards require a separation of the contacts
of at least 3 mm in each pole (EN 60335-1).
• The plastic case has an IP55 insulation; to connect
flexible or rigid pipes, use pipefittings having the
same insulation level.
• Installation requires mechanical and electrical skills,
therefore it shall be carried out by qualified
personnel only, who can issue the Compliance
Certificate concerning the whole installation
(Machine Directive 98/37/EEC, Annex IIA).
• The automated vehicular gates shall comply with the
following rules: EN 12453, EN 12445, EN 12978
as well as any local rule in force.
• Also the automation upstream electric system shall
comply with the laws and rules in force and be
carried out workmanlike.
• The door thrust force adjustment shall be measured
by means of a proper tool and adjusted according to
the max. limits, which EN 12453 allows.
• We recommend to make use of an emergency
button, to be installed by the automation (connected
to the control unit STOP input) so that the gate may
be immediately stopped in case of danger.
All manuals and user guides at all-guides.com
9

CONFORMITY TO REGULATIONS

V2 ELETTRONICA SPA declares that the components
included in the kit are in conformity with the provisions
of the following EC directives:
73/23/EEC electrical safety
93/68/EEC electromagnetic compatibility
99/05/EEC radio directive
98/37/EEC machine directive
and with the standards referenced here below:
73/23/EEC
ECO GOLD230V
EN 60335-1
ECO GOLD127V
PRGS433PPV2E
EN 60335-1
PRGSPPV2127E
TSC-4 EN 60335-1
RIF50 /
EGG220 EN 60598-2-1
Note: Declares that the above mentioned devices may
not be operated until the machine (automated gate) is
identified, CE-labeled, and declared to be compliant to
the specifications of Directive 89/392/EEC and follo-
wing modifications.
The person in charge for the machine start-up must pro-
vide the following records:
• Technical specification paper
• Declaration of conformity
• CE-labeling
• Testing record
• Maintenance record
• Operation manual and directions
Racconigi 28/01/2003
V2 ELETTRONICA SPA legal representative
A. Livio Costamagna
93/68/EEC 99/05/EEC
EN 61000-2-3
EN 61000-3-3
/
EN 55014-1
EN 55014-2
EN 301489-3 EN 300220-3
EN 301489-3 EN 300220-3
EN 50082-1
/
EN 50082-2
EN 50082-1
/
EN 50082-2