Hoshizaki IM-240DME Manual De Instrucciones página 2

IMPORTANT
. This booklet is an integral and essential part of the product
and should be kept and preserved by the user. Please
read carefully the guidelines and warnings contained herein
as they are intended to provide the user with essential
information for the continued safe use and maintenance
of the product. In addition, it provides GUIDANCE ONLY
to the user on the correct services and site location of the
icemaker. Please preserve this booklet for any further
consultation that may be necessary.
2. This is a commercial icemaker, and should be destined only
to be used for the purpose for which it has been expressly
designed and attached to a suitable Storage Bin as specified
by Hoshizaki. Any other use should be considered improper
and therefore dangerous. The manufacturer will not be held
liable or responsible for any damage caused by improper,
incorrect and unreasonable use.
I. INSTALLATION INSTRUCTIONS
WARNING
The installation must be carried out by qualified personnel,
in accordance with current regulations, according to the
manufacturer's instructions.
1. LOCATION
IMPORTANT
. This icemaker is not intended for outdoor use. Normal
operating ambient temperature should be within °C to 40°
C. Normal operating water temperature should be within 5°
C to 35°C. Operation of the icemaker, for extended periods,
outside of these normal temperature ranges may affect
production capacity.
2. The icemaker should not be located next to ovens, grills or
other high heat producing equipment.
3. The location should provide a firm and level foundation for
the equipment.
4. Allow 5 cm clearance at rear, sides and top for proper air
circulation and ease of maintenance and/or service should
they be required. For air-cooled model only, allow 30 cm
clearance at the right side.
5. This appliance is not suitable for installation in an area where
a water jet could be used and where dripping is not allowed.
6. Do not place anything on top of the icemaker or in front of the
Louver.
7. This icemaker will not work at subfreezing temperatures. To
prevent damage to the water supply line, drain the icemaker
when air temperature is below zero (see "II. 2. PREPARING
THE ICEMAKER FOR LONG STORAGE").
2. ELECTRICAL CONNECTIONS
WARNING
THIS APPLIANCE MUST BE EARTHED
This icemaker requires an earth that meets the national
and local electrical code requirements. To prevent possible
severe electrical shock to individuals or extensive damage to
equipment, install a proper earth wire to the icemaker. Remove
the plug from the mains socket before any maintenance, repairs
or cleaning is undertaken.
* This icemaker must have a separate power supply or receptacle of
220 - 240V.
* Stacked icemakers should each have a separate receptacle, but
they must all be connected in parallel to the same single phase
supply or circuit with sufficient ampacity.
All manuals and user guides at all-guides.com
* The main control box fuse is rated at 5A and should only be replaced
* Usually an electrical permit and services of a licensed electrician are
* If the supply cord and the plug should need to be replaced, it should
For the U.K. and the Republic of Ireland only
* The wires in the mains lead are coloured in accordance with the
* Should the socket outlets in the installation site not be suitable for
* The non-rewirable plug must never be used without a fuse cover
3. WATER SUPPLY AND DRAIN CONNECTIONS
Note: A plumbing permit and services of a licensed plumber may be
* Only potable water should be used for the icemaker.
* Water supply pressure should be minimum 0.5 bar and maximum 8
* The icemaker drain is gravity flow, so ensure drain pipe has an
* Water should drain into an open trap.
II. OPERATING INSTRUCTIONS

by a qualified service engineer.
required.
only be done by a qualified service engineer.
following code:
Green & Yellow = Earth
Blue = Neutral
Brown = Live
As the colours of the wire in the mains lead of this appliance may
not correspond with the coloured markings identifying the terminals
in your plug, proceed as follows:
The wire which is coloured Green-and-Yellow must be connected
to the terminal in the plug which is marked with the letter E or by
the symbol or coloured Green or Green-and-Yellow. The wire
which is coloured Blue must be connected to the terminal which
is marked with the letter N or coloured Black. The wire which is
coloured Brown must be connected to the terminal which is marked
with the letter L or coloured Red.
the plug supplied with your product, the plug must be removed (cut
off if it is moulded on plug) and an appropriate plug fitted.
If the non-rewirable plug has been cut from the power supply cord,
it must be disposed of. There should be no attempt to reuse it.
Inserting such a plug into a socket elsewhere presents a serious
risk of electrical shock.
being fitted.
The correct replacement for the detachable fuse cover is identifiable
from the manufacturer's reference number stamped on the plug.
Supply of replacement fuse covers can be obtained from Hoshizaki
Parts/Service Centres.
Fuses should be rated at 3A and approved to BS 362.
required in some areas.
bar. If the pressure exceeds 8 bar, use a proper pressure reducing
valve. Do NOT throttle back the supply tap.
adequate pitch or fall.
WARNING
. This icemaker is designed to produce edible ice. To keep the
icemaker hygienic:
* Wash your hands before removing ice. Use the Plastic
Scoop provided (accessory).
* The Storage Bin is for ice use only. Do not store anything
else in the Bin.
* Clean the Storage Bin before use (see "III. . CLEANING").
ENGLISH