Machines With Isteam Automatic System; Heating Milk Or A Drink (Isteam); Preparing Frothed Milk (Isteam); Programming Functions - Rancilio CLASSE 8 DE Manual De Instrucciones

Models DE
For these models, hot water is dispensed in specific
quanities (see paragraph 9, adjusting the dose of
hot water).
To dispense hot water in different quantities, proceed
as follows:
● Hold down the delivery control 5B Fig.7 for at least
four seconds then release the button; the machine
continuously delivers water.
● When the desired measure has been obtained,
press the button again to stop delivery.
When the dose of hot water is being delivered electro-
nically, delivery can be interrupted by pressing the
button 5B.
When purified water is used, these beverages often
assume a darker colour. Should the user prefer a
lighter coloured drink, draw fresh water from an
ordinary tap and proceed with the steps for heating
a beverage as described in point 8.3.

8.5. Machines with iSteam automatic system

(Fig.7) (only Mod. DE)

8.5.1 Heating Milk or a Drink (iSteam)

● Immerse the wand in the milk or drink.
● Press steamed milk button (6.2 on Fig. 7) on the
steam wand
● The display will show the temperature of the
drink.
● Press steamed milk button (6.2) again to stop
heating at the desired temperature.
● Wait for the machine to stop automatically at the
programmed temperature.

8.5.2. Preparing Frothed Milk (iSteam)

● Immerse the wand in a container containing at
least 250 cc of milk (the sensor must be at least
3 cm below the water level).
To obtain best results, use refrigerated milk (≤ 5°C)
- (≤ 41°F)
● Press the foamed milk button (6.1 on Fig. 7) on
the steam wand
● The display shows the temperature of the milk.
● Press the foamed milk button (6.1) again to stop
the machine at the desired temperature and
emulsion level.
● Wait for the machine to stop automatically at the
set temperature and level of froth.

8.6 Programming functions

8.6.1 Programming Panel (Mod.DE)

Use the keys of the first group head, which have the
following programming functions (Fig. 10):
1° Button "+" To move to a higher level in the
programming menus. Or to
increase the value
2°Button "-" To move to a lower level in the
programming menus. Or to
decrease the value
All manuals and user guides at all-guides.com
3° Button "enter" To enter the programming
menu. Or to confirm entries
4° Button "esc" To quit the menu
Or to quit programming mode.
5° Button Key off.
8.7 Barista Programming (Mod.DE) (Fig.12)
By holding in on key 1 of the first group of keys (1st
key on the left), for 8 seconds you will enter the pro-
gramming mode.
By pressing "+" and "-" keys the following sub-menus
will be browsed:
Programming with the following sub-menus:

- Clock

- Set date
- Set time
- Date/time format

- Set timer

- Stand by timer
- Sunday
8.7.1.Clock
Sub-menu to set date and time and mode (24 hours
or English 12 hours and date with dd/mm/yy or
mm/dd/yy)
8.7.2 Set timer
Menu to set automatic switching on/off of the machine
as follows:
- select automatic or manual switching on (to enable
function or not)
- set switching on time for every day of the week
- set working hours
To browse from one menu to another press "+" or "-",
to enter a sub-menu or to confirm a variation press
"enter", to exit press "esc".
The value that can be modified with "+" or "-" keys
is flashing.
8.7.3 Timer-cut-out (Fig.13)
If the machine is turned off by the programme and
you would like to turn it back on, you can press and
hold button 4 (of the first group heads keys) for 3-
4 seconds. The machine will then turn on and will
remain on until it has reached it's programmed turn-
off time or you may turn it off by pressing the same
number 4 button again.
If the machine is turned on automatically by the
programme you may also turn the machine off by
pressing and holding button 4 (of the first group head
keys) for 3-4 seconds. The machine will remain tur-
ned-off until you turn it back on using the number 4
button or the programmed time arrives.
57