Aventics AF2 Instrucciones De Servicio página 20

AVENTICS | AF2 | R412026496–BAL–001–AA | English
8/4 , 9/4
Counter
Viewing the counters
O
Select from the submenus Mass, Volume, Energy, and lastReset, to view the counters.
Resetting counters
O
Select the Reset submenu to reset the counters.
8/4 , 9/4
System
Service login
O
Go to the Service submenu to perform a service login for authorized users.
Resetting to the factory settings
O
Go to the FactReset submenu to reset the system to the factory settings.
Serial Number (read only)
O
Go to the SerialNumber submenu to view the serial number.
Setting the device tag
O
Go to the DevTag submenu to set the device tag.
Setting the application tag
O
Go to the AppTag submenu to set the application tag.
FWVersion (read only)
O
Go to the FWVersion submenu to view the firmware version.
Calibration (read only)
O
Go to the Calibration submenu to view the firmware defaults.
BLVersion (read only)
O
Go to the BLVersion submenu to view the bootload version.
HWVersion (read only)
O
Go to the HWVersion submenu to view the hardware version.
Operating the Ethernet version
9/1
Ethernet
Applies to all flow rate sensors with type code Flow rate sensor ASx-AF2-ETH.
The following section lists the recommended settings in the respective submenus from top to
9/1 9/4
bottom, see also Fig. to .
O
Assign a static or dynamic address.
O
Go to the DHCP Mode submenu to assign the address.
Setting the IP address
O
Go to the IP Address submenu to set the IP address.
SubNetMask
O
Go to the SubNetMask submenu to set the subnet mask.
Gateway
O
Go to the Gateway submenu to set the gateway address.
9/1
Webserver
Switching the web interface on and off
O
Go to the State submenu to switch between Active and Inactive.
Setting the port
O
Go to the Port submenu to set the port.
Resetting the user password
O
Go to the ResetPW submenu to reset the user password on the web server.
9/1
OPC UA
Switching the web interface on and off
O
Go to the State submenu to switch between Active and Inactive.
Setting the port
O
Go to the Port submenu to set the port.
Setting the user name
O
Go to the User submenu to set the user name.
Assigning a new password
O
Go to the Password submenu to set the password.
9/1 , 9/2
MQTT
Switching the web interface on and off
O
Go to the State submenu to switch between Active and Inactive.
Broker
O
Go to the Broker submenu to set the broker.
Setting the port
O
Go to the Port submenu to set the port.
Topic
O
Go to the Topic submenu to view the topics.
User
O
Go to the User submenu to set the user name for the broker.
Setting the broker password
O
Go to the Password submenu to set the broker password.
Sending the update interval to the broker
O
Go to the Update submenu to set the interval.
QoS
O
Go to the QoS submenu to enter QoS-0, QoS-1, or QoS-2.
Defining an MQTT message to the broker
O
Go to the Send submenu, select a menu item from the second submenu
(Unit to AppStatistic), and select Active or Inactive.
Operating the IO-Link version
Applies to all flow rate sensors with type code Flow rate sensor ASx-AF2-FLX.
The display shows the measured value menu with the default setting (kg/h, m/s).
O
Press any arrow button for at least 2 seconds and select Q1 Menu, Q2 Menu, or Qa Menu.
The following section lists the recommended settings in the respective submenus from top to
8/1 8/2
bottom, see also Fig. to .
W
Q1 Menu and Q2 Menu can be used to set the switch output.
W
Qa Menu can be used to set the analog output.
8/1
Q1 Menu
This menu contains the settings for switch output 1.
Setting the hysteresis or window function
O
Go to the Mode menu to set the mode for hysteresis or window function with the associated
measurement parameters.
Setting the switching point
O
Go to the SetPoint1 submenu to set the switching point.
Setting the resetting point or lower window limit
O
Go to the SetPoint2 submenu to set the resetting point/hysteresis or the lower window limit.
Setting the break contact switching characteristics
O
Go to the Polarity submenu and select NormallyClosed or NormallyOpen.
Simulating the switch output
O
Go to the Simulate submenu and select Active, Inactive, or Normal (measuring operation).
Setting PNP/NPN or push-pull (DRV)
O
Go to the DriverType submenu and set PNP, NPN or push-pull (DRV).
8/1 , 8/2
Q2 Menu
This menu contains the settings for switch output 2.
Setting the switch output as frequency, pulse, analog, or switch output
O
Go to the Function submenu to make the corresponding setting.
Setting the mode for hysteresis or window function
O
Go to the Mode submenu to make the corresponding setting.
Setting the switching point
O
Go to the SetPoint1 submenu to set the switching point.
Setting the resetting point or lower window limit
O
Go to the SetPoint2 submenu to set the resetting point/hysteresis or the lower window limit.
Setting the break contact switching characteristics
O
Go to the Polarity submenu and select NormallyClosed or NormallyOpen.
Simulating the switch output
O
Go to the Simulate submenu and select Active, Inactive, or Normal (measuring operation).
Setting PNP/NPN or push-pull
O
Go to the DriverType submenu and set PNP, NPN or push-pull (DRV).
18