Display Backlight; Display Contrast; Internal Relay - Farfisa PDX2000 Manual Del Usuario

Ringer tones volume
Ringing volume is the same for all the kind of calls.
- To adjust it select "Ringer tones
vol." and press - an adjusting
bar is displayed on the screen - with
the buttons or
volume - press - select "Save"
- press .
Ringing Tones can be disabled choosing the lowest level
of volume in this menu or directly from the Device Man-
ager menu.
Ringing volume can be also momentarily adjusted acting
on the buttons or

Display Backlight

Select Display Backlight - press
- chose the desired color from the list
or set a new color - press
"Save" - press .

Display contrast

Select LCD Contrast - press
an adjusting bar is displayed on the
screen, adjust the contrast of LCD
acting on the buttons
press - select "save" - press
Advanced and System settings
Advanced and system settings are fundamental for the
correct working of the system, therefore they are acces-
sible only entering a 4-digit password. By factory default
the passord is 1234. It is advisable to change it with a per-
sonal one (see chapter "Password").
Attention. It advisable to write down the new password
and keep it in a safe place; If you lose the password please
refer to FARFISA technical support.
Advanced
To access the advanced menu:
Press - select "Settings" - press
vanced" - press - enter the 4-digits password - press
- the following functions will be listed: Password,
Relay Mode, Relay Timing, Others, Restore Factory Settings,
Clear ALL bookings, Clear ALL alarms, Delete List, Recovery
Directory and Diagnostic.
Menu
Alarms
Display backlight
Mode
Display contrast
- Settings
- Advanced
Changing Password
To change the password it is necessary:
- select "Password" – press
to erase the actual password –en-
ter the new 4-digits password - press
- select "Save" - press
New password in now stored.
Ringer tones volume
adjust the
while receiving a call.
Display Backlight
- Red
Green
- select
Blue
-
Display contrast
50%
or -
.
- select "Ad-
Settings
21.09.11
####
- press
Programming system
password
1234
.
Operating mode of the internal relay.
Relay inside the switchboard (terminal boards C, NC, NO)
can be used for:
- additional ringer for the incoming calls, a lamp signaller
can also be driven
75%
- power-ON a CCTV monitor only during the calls from the
door stations
- bistable relay operated by the button
is activated the LED
- monostable relay operated by the button
relay is activated the LED
should be set according the instructions of chapter "Tim-
ing of internal relay".
- remain activated when the doorkeeper excanger is
switched to night mode.
To set the operating mode it is neces-
sary: - select "Relay Mode" - press
- select the requested mode - press
- select "Save" - press
Timing of internal relay
To set the activation time of relay, only
when the relay operates as "Additional
ringer tone" and "Monostable", it is
necessary: - select "Relay Timing" –
press - press
activation time – enter the new activation time in seconds
(from 1 to 99 sec.) - press
Others
To operate these functions the assistance of a Farfisa
technician is necessary.
- Save DUO Logs
- LED x debug
- Video always ON
- Master flag ON
Factory settings
To restore the factory settings and reset all the data pre-
viously programmed (except the directory) it is necessary:
-select "Restore Factory Settings" -
press - select YES to confirm or
NO to exit - press
Clear all bookings
To cancel all the booking queue:
-select "Clear ALL bookings" – press
- select YES to confirm or NO to
11.06
exit - press
Clear all alarms
To cancel all alarms:
-select "Clear ALL Alarms" – press
- select YES to confirm or NO to exit -
press .
will light-Up
will light-Up, timing of relay
- Addit.ringer tone
Monitor door sta
Bistable
.
Programming relay time
to erase the previous programmed
- select "Save" - press
Restore Factory Set.
.
Clear ALL bookings
.
Mi 2453/2
; when the relay
; when the
Relay Mode
activation
30
.
NO YES
NO YES
Clear ALL alarms
NO YES
- 25 -