Black and Decker BES720 Traducido De Las Instrucciones Originales página 12

ENGLISH
Ensure that the legs always slope outwards as shown on front
cover and assembly drawing on page 2.
Unscrew and remove all four leg stand locking knobs (12)
u
as shown in figure A.
Place the table saw upside down on a stable surface, and
u
insert the leg stands (9) as shown in figure B.
Ensure correct orientation.
Replace the leg stand locking knobs (12) ensuring they
u
pass through the holes on the leg stands (9) and tighten
securely, as shown in figure B.
The table saw comes with a leg stand level adjustor (22),
u
this can be adjusted to compensate for irregular floors, as
shown in figure C.
Riving knife set-up (Fig. D, E & F)
Warning!
The riving knife (3) should be delivered in the cor-
rect position for through cutting. However, before first use and
before connecting the machine to the power, make sure the
riving knife is secure, in-line with the blade and the correct dis-
tance from the blade - see fig F. Only work with the machine
if the riving knife (3) is in the upper position unless the saw
is being used for slitting operations. THE GUARD MUST BE
REMOVED FOR SLITTING OPERATIONS. IMMEDIATELY
RAISE THE RIVING KNIFE AND REATTACH THE GUARD
AFTER COMPLETING ANY OPERATION WHICH REQUIRES
REMOVAL OF THE GUARD OR LOWERING OF THE RIV-
ING KNIFE. Fitting the riving knife (3) in the upper position
is as follows:
Remove the securing screw (20a) on the table insert (20)
u
and lift the table insert clear from the saw, as shown in
figure D.
Raise the saw blade and riving knife assembly by turning
u
the blade elevation handle (11) clockwise, as shown in
figure E.
Loosen the locking handle (3a) and pull the riving knife (3)
u
into the upper position, as shown in figure F.
Return the locking handle (3a) to the locked position.
u
Warning! If the locking handle (3a) cannot be positioned in
the lower quadrant locked position (Fig. F) the riving knife
may not be correctly located.
Reposition the riving knife and reset the locking handle in the
lower quadrant position.
Warning! The Locking Handle (3A) Must Be In The Lower
Quadrant, Below Horizontal Position - See Fig F , To Be Fully
Locked. Check This Carefully.
Blade guard assembly (Fig. G)
Warning! The riving knife must be locked in the upper position
before fitting the guard.
The guard must not be fitted when the Riving knife is located
and locked in the lower position.
12
(Original instructions)
The blade guard (2) is supplied with a spring-loaded
u
locking pin (2c) to locate and secure the guard to the
riving knife (3). The guard must be fitted when making
through cuts to reduce the risk of injury.
Raise the saw blade and riving knife assembly by turning
u
the blade elevation handle (11) anti-clockwise as shown in
figure E.
Locate the bar in the rear of the guard (2b) downwards
u
and to the rear of the riving knife location (3b).
Press the locking pin (2c) and lower the guard to align with
u
the riving knife front location (3c)
Release the locking pin and confirm the guard is secure
u
on the riving knife.
The operator should only be able to remove the guard
u
from the riving knife by depressing the locking pin (2c) and
then lifting the guard upwards.
Gently tug the guard up from riving knife to ensure this is
u
fully fitted.
Dust management
Your saw is provided with a dust bag (7) which should be
u
attached to the dust port on the rear of the unit (as shown
on page 3) if a vacuum is not being used.
If you wish to use a vacuum cleaner both the guard port
u
and the rear port are suitable for 35mm nozzles. the
vacuum cleaner must be suitable for the material being
worked.
When vacuuming dry dust that is especially detrimental
u
to health or carcinogenic, use dust class M vacuum
cleaner.
Ensure that the dust extraction hose in use is suitable
u
for the application and material being cut. Ensure
proper hose management
Saw blade assembly/replacement (Fig. O)
Warning! Always check alignment of riving knife and function-
ality of guards after any maintenance.
Warning! Always check the Riving knife is locked in position
and aligned with the blade before each use and after any
maintenance.
The guard must be fitted when making through cuts.
Warning! Ensure the machine is disconnected from the
power source. Wear safety gloves.
Disassemble the saw blade guard (2).
u
Remove the table insert (20).
u
Loosen the saw blade nut by placing the spanner wrench
u
(17) on the nut and countering with another spanner
wrench (17) on the flange.
Warning! Turn the nut in the rotational direction of the saw
blade.
Remove the outer flange and take out the saw blade from
u
the inner flange, with diagonal downward movement.