SOUNDMASTER highline UR2160 Manual Del Usuario página 19

CD programming
Up to 20 tracks can be programmed for disc play in any order. Before use, be sure to press the " stop
1. Set in CD mode & stop the CD playback.
2. Press the " Mem/Clk-Adj " button (11) and " MEM " will appear on LCD display (13).
3. Select a desired track by pressing skip up
4. Press the " Mem/Clk-Adj " button (17) to store the track into memory.
5. Repeat steps 3 and 4 to enter additional tracks into the memory if necessary.
6. When all the desired tracks have been programmed, press " Play/Pause
7. Press " Stop " button (8) to stop playback, press Stop button again to clear all stored memory.
¾
The programming mode will automatically stop if no button is being pressed in a period of about 10 seconds after pressing
the "Mem/Clk-Adj " button.
Playback of MP3 song via USB storage media
Connecting
The system is able to decode and playback all MP3 file which stored in the memory media with USB connecting port.
1. Set the system at standby mode first or other function except USB mode.
2. Open the USB socket cover and plug-in the USB pen-drive with the face up & make sure it going into
completely.
z
Connecting the USB upside down or backwards could damage the audio system. Check to be
sure the direction is correct before connection.
3. Set Function button (16) to "
4. The system will start reading the storage media automatically after connecting, and LCD display (13)
will show the total number of folder and MP3 files being detected.
5. Repeat the same playback procedure as playing CD/MP3 disc as above.
Remark
- The system can detect and read the file under MP3 format only at USB mode but not other music file format.
- If connect the system to MP3 player via the USB socket, due to variances in MP3 encoding format, some MP3
player may not be able to play via the USB socket. This is not a malfunction of the system.
- USB port does not support connection with USB extension cable and is not designed for communication with
computer directly
Removing of USB
To remove the USB storage media, change the function mode to either CD, Aux, or Tuner first. Then un plug it by pulling out the
USB socket directly.
More features
A. Sleep function
1. Press " Sleep " button (on Remote) "SLP-90 " will shown on the LCD display (1).
2. Keep pressing the button to adjust the sleep timer in the order of 90 > 80 > 70 >....10 minutes respectively and sleep icon
" " will indicate on LCD.
3. System will stop and go to standby mode automatically after running the selected time.
4. To cancel the sleep mode, press " Sleep " button until "SLP-off' displayed and the "
display.
B. Cooking timer
This system had cooking timer function from 1 to 120 minutes to remind your cooking state by bee tone sound.
Press and hold the " Timer " button(19) to enter the timer setting mode, the first digits of display and timer icon
Press Volume button (14) to adjust the countdown minute, the display will run up from 1 minute to 120 minutes maximum. Then
press " Timer " button (19) to confirm the countdown time, then press Volume button (14) to adjust the bee tone volume level.
Press the " Timer " button to complete the timer setting. System will start to countdown automatically and display will change to
countdown state. Once countdown was arrived, bee tone sound will coming.
Remark:-
¾
There are about 6 seconds for timer setting mode, this system will return to normal mode automatically if no keys being
pressed in this time frame.
¾
You still can enjoy your music during timer countdown. Once countdown was arrived, the system will generate a bee tome
sound instead of your playing music, just press " Timer " button(19) to switch off the timer bee tone sound then your music
will resume playing.
¾
You also can disable the timer function anytime by press " Timer " button(19) until the timer icon
or down
" USB mode.
E'
hZ
button (9).
" button (7) to play the disc in assigned order.
" button (8).
" indicator disappear on LCD
will flashing .
disappear.