Setting The Clock - SOUNDMASTER highline UR2160 Manual Del Usuario

Install to your kitchen cabinet
1) Use the mounting template supplied with the unit to make anchor hole marks on the kitchen
cabinet.
2) Drill 1/4" holes on the marks.
3) Fix the plastic pole(provided) to top of the unit with the proper high level which can match
your kitchen cabinet.
4) Drive the provided screw from the kitchen cabinet to the main unit(refer to the picture).
Connection
1. Plug in the AC cord (25) to the AC outlet. The unit will go to standby mode and the Standby LED indicator (1) will light up.
2. Turn on the unit (15), if the LCD display (13) is on with backlighting, it means the power supply is normal. Now your system
is ready to play the music.

Setting the clock

1. Set unit in standby mode.
2. Press the " Mem/Clk-Adj " button (11) until display will flash "24HR" press the Skip Up
select the clock format between 12 or 24Hour. Then press the " Mem/Clk-Adj " button (11).
3. The first digit of " 0:00 " is flashing on the LCD display (13). Press Skip Up
correct hour. Press " Mem/Clk-Adj " button (11) to store the correct hour.
4. The third & fourth digit of " 00 " is flashing, press the Skip Up
Then press " Mem/Clk-Adj " button (11) to store the correct minute.
¾
The clock setting mode will automatically quit if no button is being pressed in a period of about 5 seconds after
pressing the " Mem/Clk-Adj " button.
¾
The pre-set time will be re-set completely if dis-connecting the main power supply except backup
battery installed. You are recommended to switch the system into standby mode for convenience
usage.
Listening to radio
Manual tuning
1. Switch on the unit by On/Standby button (15), then press Function button (16) to select " Tuner " mode.
2. Tune to the required station by pressing the Tuning Up or Down button (9).
3. Press the Volume knob (14) to the desired volume level.
Auto tuning
1. Press Function button (16) to select " Tuner " mode.
2. Press and hold the Tuning Up or Down button (9) for 1-2 seconds and then release.
3. The unit will start seeking automatically and stop until a radio station is reached.
4. Repeat step 2 & 3 until the desired radio station is being reached.
5. Press Volume knob (14) to the desired volume level.
Preset stations
You can store up to 20 radio stations in the memory
Set to tuner mode.
1. Turn to the desired radio station by " Manual" or " Auto " tuning method.
2. Press the Mem/Clk-Adj " button (11) until the " MEM " indicator and preset station number are flash on LCD display (13)
3. Press " Folder / Pre-up
4. Press " Mem/Clk-Adj " button (11) again to confirm the setting.
5. Repeat step 1 to 4 to store other stations.
6. Now you can select the presets stations in order by pressing the "Folder/Pre–up
¾
The pre-set memories will be cancelled completely if dis-connecting the main power supply except backup battery
installed. You are recommended to switch the system into standby mode for convenience usage.
¾
There are 5 seconds for program state, after 5 sec. This state would resume to normal tuner mode automatically.
¾
You can overwrite a present station by storing another frequency in its place.
Radio data system (RDS)
This is the features to display the information which released from the radio broadcast:-
RDS mode : Press RDS mode button( 18) to active the RDS function and the program service station name (PS) is being
displayed.
/down "button (10) to select the desired station memory for storage.
or Skip Down
E'
hZ
or Skip Down
or Skip Down button (9) to set the
button (9) to set the correct minutes.
/down "button (10)
button (9) to