Beware Of Condensation; Before Use - Teac P-70 Manual Del Usuario

Read this before operation
< As the unit may become warm during operation, always leave
sufficient space above the unit for ventilation.
< The voltage supplied to the unit should match the voltage as
printed on the rear panel. If you are in any doubt regarding this
matter, consult an electrician.
< Choose the installation location of your unit carefully. Avoid
placing it in direct sunlight or close to a source of heat. Also
avoid locations subject to vibrations and excessive dust, heat,
cold or moisture.
< Do not place the unit on the amplifier/receiver.
< Do not open the cabinet as this might result in damage to the
circuitry or electrical shock. If a foreign object should get into
the set, contact your dealer.
< When removing the power plug from the wall outlet, always
pull directly on the plug, never yank the cord.
< To keep the laser pickup clean, do not touch it, and do not
forget to close the disc tray.
< Do not attempt to clean the unit with chemical solvents as this
might damage the finish. Use a clean, dry cloth.
< Keep this manual in a safe place for future reference.
DO NOT MOVE THE UNIT DURING PLAYBACK
During playback, the disc rotates at high speed. Do NOT lift or
move the unit during playback. Doing so may damage the disc.
WHEN MOVING THIS UNIT
When changing places of installation or packing the unit for
moving, be sure to remove the disc and return the disc table to
its original position in the player. Then, press the power switch
to turn the power off, and disconnect the power cord. Moving
this unit with the disc loaded may result in damage to this unit.

Beware of condensation

When the unit (or a disc) is moved from a cold to a warm place, or
used after a sudden temperature change, there is a danger of
condensation; vapor in the air could condense on the internal
mechanism, making correct operation impossible. To prevent this,
or if this occurs, leave the unit for one or two hours with the
power turned on. Then the unit will stabilize at the temperature of
its surroundings.
Maintenance
If the surface of the unit gets dirty, wipe with a soft cloth or use
diluted neutral cleaning liquid. Be sure to remove any fluid
completely. Do not use thinner, benzine or alcohol as they may
damage the surface of the unit.
CAUTION
The product shall not be exposed to dripping or splashing and
that no object filled with liquids, such as vases, shall be placed
on the product.
Do not install this equipment in a confined space such as a
book case or similar unit.
All manuals and user guides at all-guides.com

Before Use

Releasing the anti-vibration clamp
When the P-70 is shipped from the factory, the pickup is secured
with an anti-vibration clamp in order to reduce vibration during
transport. This must be released before use.
1. Place the unit on its side, left side down, as shown here.
2. Use the supplied tool and insert it into the hole on the bottom.
3. Turn the tool about 30 degrees counter-clockwise in the FREE
Securing the anti-vibration clamp
If you are going to transport the unit, you must secure the clamp
in position.
1. Remove any disc from the unit, disconnect the power, and
2. Use the supplied tool and insert it into the hole on the bottom.
3. Turn the tool about 30 degrees clockwise in the LOCK
NOTE:
You do not need to use force to clamp and unclamp the unit. This
may damage the unit. Use only the supplied tool and turn gently.
Placement of the unit
High-quality hardened tool steel is used for the pin-point feet,
securely attached to the bottom of the player. Although the cover
feet may appear loose, the weight of the unit causes them to be
firm and secure, and the design effectively damps and reduces
vibration.
< Be careful to avoid injury when moving the unit, on account of
< To protect floors, etc. you may stick the felt supplied with the
direction.
place the unit on its side, left side down, as shown here.
direction.
its weight. Get someone to help you if necessary.
unit to the bottom of the cover feet.
Pin-point foot
Steel foot
Cover foot Cover foot retaining screws
Bottom plate
of the unit
5