Parameter Management - Parker Hiross Hyperchill ICE310 Manual De Uso

4.4.1.1 Remote On / Off mode
0
Remote On/Off disabled
1
Remote On/Off enabled together with local On/Off
2
Remote On/Off only, local On/Off disabled
4.4.1.2 Alarm relay management
0
Relay normally deactivated, excited by an alarm.
Relay normally excited (also with control OFF), deactivated
1
by an alarm.
Relay normally excited (only with control ON), deactivated
2
by an alarm or with control OFF.
4.4.2 Temperature control
PARAMETER CODE
SEt
Temperature control set point
dIF
Temperature control diff erential
LI5
Set point lower limit
4.4.3 B1 sensor parameters
PARAMETER CODE
cHAI
High temperature confi guration
HAI
High temperature alarm
LAI
Low temperature alarm
CAI
Sensor calibration
Low temperature alarm reset
dbI
diff erential
4.4.4 B2 sensor parameters
PARAMETER CODE
cHA2
High temperature confi guration
HA2
High temperature alarm
LA2
Low temperature alarm
CA2
Sensor calibration
Ab2
B2 sensor presence
4.4.5 P1 sensors parameters
PARAMETER CODE
CAP1
Transducer calibration
4.4.6 P2 sensors parameters
PARAMETER CODE
CAP2
Transducer calibration
English
4.4.7 Compressor parameters
PARAMETER
Compressor rotation
Compressor 1 enabling
Compressor 3 enabling
Compressor 2 enabling
Compressor 4 enabling
Compressor 1 operation hour
counter
Compressor 3 operation hour
counter
Compressor 2 operation hour
TYPE DEFAULT
counter
12.0
D
Compressor 4 operation hour
3.0
D
counter
5.0
U
Compressor 1 hour counter
threshold
Compressor 3 hour counter
TYPE DEFAULT
threshold
0
U
Compressor 2 hour counter
60.0
D
threshold
-20.0
D
Compressor 4 hour counter
0.0
U
threshold
4.4.8 Pump parameters
1.0
U
PARAMETER
Pump stop delay
TYPE DEFAULT
Pump start delay
0
U
60.0
U
3.0
U
0.0
U
1.0
U
TYPE DEFAULT
00
U
TYPE DEFAULT
00
U
CODE TYPE DEFAULT
rot 2
U
AbC1 0
U
AbC3 0
U
AbC2 0
U
AbC4 0
U
D
HI -
D
H3 -
D
H2 -
D
H4 -
tHI 0
U
tH3 0
U
tH2 0
U
tH4 0
U
CODE TYPE DEFAULT
dP5 5
U
dPA 5
U
ICE310-360

4.5 Parameter management

4.5.1 Temperature setting (see fi g.1)
1. 1. Turn the main swicth (QS) to "ON" and wait for the temperature
visualization.
2. Press buttons "P3" and "P5" together, to enter into "dIrE" (D)
parameters.
3. Press button "P4" to select "SEt" parameter, press the button
"P5" to confi rm.
4. Change the value, using the up and down arrow buttons "P3" and
"P4", then press button "P5" to confi rm.
6. Press the button "P3" to return on "dIrE" parameter.
7. Press the button "P5" to exit.
4.5.2 Diff erential setting (see fi g.1)
1. Turn the main swicth (QS) to "ON" and wait for the temperature
visualization.
2. Press buttons "P3" e "P5" together, to enter into "dIrE" (D)
parameters.
3. Press button two times "P4" to select "diF" parameter, press the
button "P5" to confi rm.
4. Change the value, using the up and down arrow buttons "P3" and
"P4", then press button "P5" to confi rm.
6. Press the button two times "P3" to return on "dIrE" parameter.
7. Press the button "P5" to exit.
4.5.3 Visualization sensors B1,B2...
"B1" is the "set" sensor of the macchine.
1. Start the chiller.
2. Press the button "P4" to visualize the temperature of the next sen-
sor.
3. Press the button "P5" to visualize the sensors "b01" .."b02"....
It is recommended to leave on the display the B1 "set" sensor.
5/8