Bosch PMF 250 CES Manual Original página 15

OBJ_BUCH-1645-005.book Page 15 Wednesday, November 11, 2015 12:42 PM
Product Description and
Specifications
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Intended Use
The machine is intended for sawing and cutting wooden mate-
rials, plastic, gypsum, non-ferrous metals and fastening ele-
ments (e.g., unhardened nails, staples). It is also suitable for
working soft wall tiles, as well as for dry sanding and scraping
of small surfaces. It is especially suitable for working close to
edges and for flush cutting. Operate the power tool exclusive-
ly with Bosch accessories.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 SDS lever for releasing the application tool
2 On/Off switch
3 Thumbwheel for orbit frequency preselection
4 Venting slots
5 Handle (insulated gripping surface)
6 Auxiliary handle (insulated gripping surface)
7 Thread for auxiliary handle
8 Tool holder
9 Plunge saw blade
10 Sanding plate
11 Sanding sheet
12 Depth stop
13 Segment saw blade
14 Tool retainer
15 Vacuum hose*
16 Vacuum connection*
17 Fastening screw of the dust extraction*
18 Dust extraction*
19 Felt ring of the dust extraction*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Multi-function tool
Article number
Preselection of orbital stroke
rate
Constant electronic control
Soft starting
Rated power input
Output power
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Bosch Power Tools
Multi-function tool
No-load speed n
Oscillation angle, left/right
Weight according to
EPTA-Procedure 01:2014
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-4.
Typically the A-weighted noise levels of the product are:
Sound pressure level 84 dB(A); Sound power level 95 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Working without auxiliary handle
Vibration total values a
determined according to EN 60745:
Sanding: a
Cutting with plunge cut saw blade: a
Cutting with segmental saw blade: a
Scraping: a
Working with auxiliary handle
Vibration total values a
determined according to EN 60745:
Sanding: a
Cutting with plunge cut saw blade: a
Cutting with segmental saw blade: a
Scraping: a
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with another.
It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This may
significantly increase the exposure level over the total working
period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signif-
icantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator
PMF 250 CES from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
3 603 A00 6..
terns.

Declaration of Conformity

We declare under our sole responsibility that the product de-

scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
W 250
2006/42/EC including their amendments and complies with
W 140
the following standards: EN 60745-1, EN 60745-2-4,
EN 50581.
-1
min 15000–20000
0
°
kg
(triax vector sum) and uncertainty K
h
2 2
=10 m/s , K=1.5 m/s
h
=13 m/s
h
=14 m/s
h
2 2
=12 m/s , K=1.5 m/s .
h
(triax vector sum) and uncertainty K
h
2 2
=9 m/s , K=1.5 m/s
h
=17 m/s
h
=18.5 m/s
h
2 2
=16 m/s , K=1.5 m/s .
h
1 609 92A 1R3 | (11.11.15)
English | 15
PMF 250 CES
1.4
1.3
/II
2 2
, K=2 m/s
2 2
, K=3 m/s
2 2
, K=2 m/s
2 2
, K=3 m/s