Bosch PMF 190 E Manual Original página 16

OBJ_BUCH-345-012.book Page 16 Tuesday, November 10, 2015 5:54 PM
16 | English
Dust/Chip Extraction
 Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suitable
for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
 Prevent dust accumulation at the workplace. Dusts can
easily ignite.
Connecting the Dust Extraction (see figure A)
The dust extraction 16 is intended only when working with the
sanding plate 9; it is not of use in combination with other
application tools.
For sanding, always connect the dust extraction.
To mount the dust extraction 16 (accessory), remove the
application tool and the depth stop 11.
Slide the dust extraction 16 over and beyond the tool holder
5 to the stop onto the gear head of the power tool. Insert fas-
tening screw 15 into the corresponding recess on the hous-
ing. To lock the screw, turn it to the
Pay attention that the felt ring 17 is undamaged and faces
tightly against the sanding plate 9. Replace a damage felt ring
immediately.
Place a vacuum hose 13 (accessory) onto the vacuum con-
nection 14. Connect the vacuum hose 13 with a vacuum
cleaner (accessory).
An overview for connecting to various vacuum cleaners can be
found on the graphics page.
The vacuum cleaner must be suitable for the material being
worked.
When vacuuming dry dust that is especially detrimental to
health or carcinogenic, use a special vacuum cleaner.
To remove the dust extraction 16, turn fastening screw 15 to
the position and pull the dust extraction from the gear
head of the power tool.
Operation
Starting Operation
 Observe the mains voltage! The voltage of the power
source must correspond with the data on the type plate of
the machine.
1 609 92A 214 | (10.11.15)
Switching On and Off
To start the machine, push the On/Off switch 1 forward so
that the "I" is indicated on the switch.
To switch off the machine, push the On/Off switch 1 toward
the rear so that the "0" is indicated on the switch.
To save energy, only switch the power tool on when using it.
Preselecting the Orbital Stroke Rate
With the thumbwheel for preselection of the orbital stroke
rate 2, you can preselect the required orbital stroke rate, even
during operation.
The required stroke rate depends on the material and the
working conditions and can be determined through practical
testing.
When sawing, cutting and sanding harder materials, e.g.,
wood or metal, it is recommended to work with orbital stroke
rate "6"; for softer materials, such as plastic, orbital stroke
rate "4" is recommended.
Working Advice
 Wait until the machine has come to a standstill before
placing it down.
 Before any work on the machine itself, pull the mains
plug.
Note: Do not cover off the venting slots 3 of the machine while
working, as this reduces the working life of the machine.
While working with HCS tools make sure that the covering of
the tools is undamaged.
Operating Principle
position.
Due to the oscillating drive the application tool/accessory
oscillates up to 21000 times per minute at 2.8°. This allows
for precise work in narrow spaces.
Sawing
 Use only undamaged saw blades that are in perfect con-
dition. Bent or dull saw blades can break, negatively influ-
ence the cut, or lead to kickback.
 When sawing light building materials, observe the stat-
utory provisions and the recommendations of the ma-
terial suppliers.
 Plunge cuts may only be applied to soft materials, such
as wood, gypsum plaster boards, etc.!
Before sawing with HCS saw blades in wood, particle board,
building materials, etc., check these for foreign objects such
as nails, screws, or similar. If required, remove foreign ob-
jects or use BIM saw blades.
Work with low and uniform application
pressure, otherwise, the working perfor-
mance will decline and the application tool
can become blocked.
While working, move the machine back and
forth, so that the application tool does not
heat up excessively and become blocked.
Bosch Power Tools