Humidifier Control Via Network; Supervisor Variable List - Carel humiSonic Manual Del Usuario

ENG
The variables shown in the list are a set of all the internal variables. DO
NOT CONFIGURE ANY VARIABLES THAT ARE NOT SHOWN IN THE TABLE,
OTHERWISE HUMIDIFIER OPERATION MAY BE AFFECTED.
The serial connection (M11) is confi gured by default with the following
parameters:
- Address 1
- Baud rate 19200 bps
- Frame 8,N,2

8.1 Supervisor variable list

"A"
analogue variables* (Modbus®: REGISTERS)
CAREL Modbus®
1 0 param. d0: Th probe temperature reading
2 1 param. d1: Th probe humidity reading
3 2
param. d2: Probe reading
4 3 param. d5: Instant production
"I"
integer variables (Modbus®: REGISTERS)
CAREL Modbus®
1 128 Level access password
7 134 Humidifi er status
0: disabled/standby
1: autotest
2: initialisation
2 129 Firmware release
15 142 Alarms, refer to Chap.8 ALARMS:
bit0: Alarm E0
bit1: Alarm Et
bit2: Alarm EF
bit3: Alarm Ed
20 147 Parameter A0: Operating mode
21 148 Parameter A2: Type of external probe
22 149 Parameter A3: Probe minimum
23 150 Parameter A4: Probe maximum
24 151 Parameter A5: Probe off set
25 152 Parameter A6: Fan off delay time
26 153 Parameter A7: Fan speed
27 154 Parameter A8: Maximum evaporation time for no production alarm
28 155 Parameter A9: Minimum evaporation time for no production alarm
29 156 Parameter b0: Operating options
30 157 Parameter b1: Time between two washing cycles
31 158 Parameter b2: Inactivity time for washing on next start
32 159 Parameter b3: Washing time (fi ll + drain)
33 160 Parameter b4: Start delay time
34 161 Parameter b5: Operating hours for CL alarm
35 162 Parameter b6: Time to display new CL alarm in minutes
36 163 Parameter b7: Transducer On/Off control interval
37 164 Parameter b8: Probe delay disconnected
38 165 Parameter b9 TAM OFF delay
39 166 Parameter bA: Maximum fi ll time
40 167 Parameter bb: Refi ll time in evaporation
41 168 Parameter bC: Maximum drain time
42 169 Parameter bd: Drain opening time to completely empty tank
43 170 Parameter bE: Delay time after measuring low level for refi lling
44 171 Parameter C0: Default display (Terminal)
45 172 Parameter C1: Parameter A0: Baud rate
46 173 Parameter C2: tLAN address (If 0 Master controller)
47 174 Parameter C3: Serial address
48 175 Parameter P0: Maximum fl ow-rate
49 176 Parameter P1: Humidity control hysteresis
50 177 Parameter P2: Low humidity alarm threshold
51 178 Parameter P3: High humidity alarm threshold
52 179 Parameter SP: Humidity set point
53 180 Parameter d3: Operating hour counter
54 181 Parameter d4: Unit hour counter (not resettable)
60 187 Request via serial (if digital 37 set)
62 189 Identifi cation of variable on slave unit to read/write from supervisor (see paragraph 14.4)
63 190 Value of variable on slave unit identifi ed by integer 62 (see paragraph 14.4)
65 192 Parameter C4: Timeout for master serial offl ine
69 196 AA: Waiting time for retry
70 197 Ab: Percentage of A8 for carrying out level test
71 198 Pn: Minimum production
72 199 bF: Drain activation delay in standby
73 200 AC: Maximum time to measure level when refi lling
74 201 Ad: Maximum time to measure high level
Direct version for room applic. +0300062IE - rel. 1.3 - 15.07.2019

8. HUMIDIFIER CONTROL VIA NETWORK

3: fi ll
4: production
5: drain
bit4: Alarm EP
bit5: Alarm PU
bit6: Alarm H ¯
bit7: Alarm H_
Note : it is recommended to set on the supervisor (master) the maximum
waiting time for a response from humiSonic - after being queried by the
supervisor - of at least 500 ms.
6: reset
7: wash
8: cleaning procedure
bit8: Alarm EE bit12: Alarm ES3
bit9: Alarm CL bit13: Alarm OFL
bit10: Alarm ES1 bit14: Alarm EL
bit11: Alarm ES2 bit15: Alarm EtL
22
R/W
R
R
R
R
R/W
R/W
R
R
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W