Technical Description; Technical Features; Safety - Calpeda GM 10 Instrucciones De Uso

1.4 Warranty
For the product warranty refer to the general terms
and conditions of sale.
The warranty covers only the replacement and
i
the repair of the defective parts of the goods
(recognized by the manufacturer).
The Warranty will not be considered in the following
cases:
- Whenever the use of the device does not conform
to the instructions and information described in this
manual.
- In case of changes or variations made without
authorization of the manufacturer.
- In case of technical interventions executed by a
non-authorized personnel.
- In case of failing to carry out adequate maintenance.
1.5 Technical assistance
Any further information about the documentation,
technical assistance and spare parts, shall be reque-
sted from: Calpeda S.p.A. (paragraph 1.2).

2 TECHNICAL DESCRIPTION

Submersible drainage pump constructed with
composite polymers developed especially for this
product.
Three lip seals in NBR.
With float switch for automatic start/stop.
2.1 Intended use
Standard construction
- For clean or slightly dirty water, with solids in
suspension up to 8 mm grain size.
- For draining flooded rooms or tanks.
- Extraction of water from ponds, flowing water or pits
for collection of rain water.
- For irrigation purposes.
- Maximum liquid temperature: 35 °C.
- Tipo di servizio: S3 40%.
- Maximum liquid density: 1100 kg/m
- Maximum immersion depth: see indicator plate
(with cable of suitable length).
For outdoor use the power supply cable must have
a length of not less than 10 m.
2.2 Improper use
The device is designed and built only for the purpose
described in paragraph 2.1.
Do not use in garden ponds, tanks or
swimming pools when people are in the
water.
The Pump cannot be used in explosive or
flammable environments.
Improper use of the device is forbidden, as is
use under conditions other than those
indicated in these instructions.
Improper use of the product reduces the safety and
the efficiency of the device, Calpeda shall not be
responsible for failure or accident due to improper
use.
GM10 Rev. 13 - Operating Instructions
2.3 Marking
The following picture is a copy of the name-plate that
is on the external case of the pump.
1 Pump type
2 Delivery
3 Head
4 Rated power
5 Tension nominale
6 Nom. motor current
7 Notes
8 Fréquence
9 Operation Duty
10 Insulation class
11 Weight
12 Power factor
13 Rotation speed rpm
14 Protection
15 Serial number
16 Certifications
17 Maximum immersion depth

3 TECHNICAL FEATURES

3.1 Technical data
Dimensions and weight (paragraph 12.1).
Nominal speed 2900/3450 rpm
Protection IP X8
Supply voltage / Frequency:
- up to 240V 1~ 50/60 Hz
Check that the mains frequency and voltage corre-
spond to the electrical characteristics shown on the
indicator plate.
Sound pressure at minimum immersion depth: < 70
dB (A).
Noise disappears or decreases when the pump is
submersed.
Maximum starts/hour: 30 at regular intervals.
Maximum permissible working pressure up to 10 m
(1 bar).
The max. inlet water pressure: PN (Pa) - Hmax (Pa).

4 SAFETY

4.1 General provisions
3 .
i
Montorso (VI) Italy IT 00142630243
1
XXXXXXX
2
Q min/max X/X m
3
H max/min X/X m
4
X kW (XHp)
5
220∆/380Y V3~50Hz
6
X/X A
7
XXXXXXXX
Before using the product it is necessary to
know all the safety indications.
Carefully read all operating instructions and
the indications defined for the different steps:
from transportation to disposal.
The specialized technicians must carefully
comply with all applicable standards and laws,
including local regulations of the country
where the pump is sold.
The device has been built in conformity with
the current safety laws. The improper use
could damage people, animals and objects.
The manufacturer declines any liability in the
event of damage due to improper use or use
under conditions other than those indicated on
the name-plate and in these instructions.
Follow the routine maintenance schedules and
the promptly replace damaged parts, this will
allows the device to work in the best conditions.
Use only original spare parts provided from
Calpeda S.p.A or from an authorized
distributor.
Don't remove or change the labels placed on
the device.
Do not start the device in case of defects or
damaged parts.
Maintenance operations, requiring full or
partial disassembly of the device, must be
done only after disconnection from the supply.
EN
16
Made in Italy
15
XXXXXXX
17
/h
3
X
m
14
IP XX
13
n XXXX/min
S.F.
12
cosø X
11
S1 l.cl. X X kg
8 9 10
Page 9 / 64