Timer-Recording Radio Programs - Sony MHC-V800 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

continued
To wake up to the radio
Tune in the preset station you want.
To wake up to a CD
Insert a CD. If you want to play it from a
desired track, do the necessary
procedures for programmed CD play.
(see "Playing Tracks in the Desired
Order (program play)".)
To wake up to a tape
Insert the tape with the side you want to
play facing forwards you. If you insert
the tapes in both decks, you will hear the
sound from deck A.
2
Turn VOLUME to adjust the volume.
The music will start playing with the
adjusted volume when the preset time
comes.
3
Press TIMER.
4
Press t SET.
5
Use the JOG dial to select either DAILY
EN
1 or 2 and press ENTER/NEXT.
30
"ON" appears and the hour digits flash
in the display.
DAILY 1
DAILY 2
6
Use the JOG dial to set the hour you
want the system to turn on and press
ENTER/NEXT.
Set the minutes in the same way. "OFF"
appears and the hour digits flash in the
display.
CD
1 2 3 4 5
6 7 8
63
125
250 500
1k
1DISC
.
CD
1 2 3 4 5
6 7 8
63
125
250 500
1k
DISC
flashing
7
Use the JOG dial to set the hour you
want the system to turn off and press
ENTER/NEXT.
Set the minutes in the same way.
8
Use the JOG dial to select a sound
source.
The display changes as follows:
TUNER
CD
TAPE
CD
1 2 3 4 5
6 7 8
63
125
250 500
1k
1DISC
Chapter 7: Additional Features
9
Press ENTER/NEXT.
The preset items appear in the display
sequentially.
10
The power comes on at the preset time
and the music will play at the volume
you selected in step 2. At the turn-off
time, the power will go off again.
To change the preset timer settings
Start over from step 1.
To check the preset timer settings
1 Press TIMER.
2 Press t SELECT and use the JOG dial to
choose the mode you want to check.
3 Press ENTER/NEXT.
The preset items appear in the display
sequentially, then the original display
returns.
To change the timer
Select the timer display you desire in step 2
of "To check the preset timer settings".
To cancel the timer
1 Press TIMER.
2 Press t SELECT and use the JOG dial to
choose "TIMER OFF."
3 Press ENTER/NEXT.
The next time you want to use the timer,
REC
select the timer display you used in step
2 (DAILY 1 or DAILY 2) and press
ENTER/NEXT.
Notes
• You cannot set the timer so that the timer
ON and OFF times are the same.
• The timer operation starts 15 seconds
before the timer ON time, if you perform
another operation during that period, the
timer operation may not be performed
TIMER
DAILY1
VOLUME
DOLBY NR OFF
correctly.
2k
4k
8k
16k(Hz)
• You cannot activate wake-up timer and
timer-recording at the same time.
flashing
• The daily timer function can not activate
during the sleep count down.
TIMER
DAILY1
If you want to wake up to different tracks
VOLUME
DOLBY NR OFF
2k
4k
8k
16k(Hz)
on a CD
Create another program (see "Playing
Tracks in the Desired Order (program
play)".) and turn off the power.
TIMER
DAILY1
VOLUME
DOLBY NR OFF
2k
4k
8k
16k(Hz)
Press POWER to turn off the system.
Timer-Recording
Radio Programs
You can set the timer to record from the
radio at a certain time. This timer works
only once for each setting.
Make sure the clock has been set correctly.
Be sure to preset the station you want to
listen to beforehand. (See "Presetting Radio
Stations".)
,9
POWER m ON
4
5
3
tSELECT
1
Press § EJECT and insert a blank tape in
deck B with the side you want to record
on facing forward.
2
Tune in a preset station you want to
record.
3
Select dual or single-sided recording.
To record
Press DIRECTION to
select
One side of the tape
A
Both sides*
ß or RELAY
* Recording always stops at the end of the
reverse side. Be sure to start from the
front side.
4
Press TIMER.
5
Press t SET.
6
Use the JOG dial to select REC and press
ENTER/NEXT.
"ON" appears and the hour digits flash
in the display.
CD
1 2 3 4 5
6 7 8
DOLBY NR OFF
63
125
250 500
1k
2k
4k
8k
16k(Hz)
1DISC
flashing
7
Use the JOG dial to set the hour you
want the system to turn on and press
ENTER/NEXT.
6,
7,
8
1
TIMER
REC
VOLUME

Publicidad

Tabla de contenido
loading

Tabla de contenido