Eurosystems Z 8 Manual De Instrucciones página 16

the operation with the handle assembled with a tightening nut (13) . The order of the assembly parts should be the same as the one shown in the picture.
For further information, please read the chapter describing the handlebars adjustment.
! ! ! ! !
ASSEMBLY OF THE THROTTLE CABLE - ENGINE DIESEL MODEL : (Fig.5)
placed on the handlebar right hand part . Fit the terminal "pad" (2) into the seat (3) and insert the protecting cover (4) into the handle housing.
! ! ! ! !
MOTORSTOP CABLE ASSEMBLY - ONLY FOR DIESEL ENGINE MODEL ( Fig. 5)
former chapter also for the left handle and fix the motorstop cable . Such cable is shown by a label sticked on it.
! ! ! ! !
THROTTLE CABLE ASSEMBLY – GASOLINE ENGINE MODEL : (Fig. 8)
engine . To complete the assembly : unscrew the nut (1) and insert the screw into the hole on the handlebar (3) , then block the throttle screwing the nut
(1) again. Please be careful to the throttle handle tightening which should be free to rotate.
! ! ! ! !
ASSEMBLY OF THE THROTTLE CABLE – HONDA ENGINE MODEL GX160 - (Fig. 8)
way (4). It is placed on the handlebar right hand part . Fit the terminal "pad" (5) into the seat (6) and insert the protecting cover (7) into the handle housing.
Please link the electric terminal (8) to the switch (9) which is place on the throttle.
! ! ! ! !
ASSEMBLY OF THE BELT-STRETCHER DRIVE CABLE (Fig. 9)
need to fit them on the driving levers which are placed on the handlebar. FORWARD SPEED : insert the terminal (3) of the cable (4) into the hole (5) of
the forward speed lever (2). Make the wire (4) assembled with the adjuster (6) to pass into the nib passing-hole (7). REVERSE SPEED : insert the
terminal (8) into the hole (9) of the reverse speed (1) . Make the cable (10) assembled with the adjuster (11) to pass into the nib passing hole . (12)
! ! ! ! !
ASSEMBLY GEARS SELECTOR LEVER (Fig. 7)
welded screw to correspond (3) on the lever with the other slot (4) . Please take care to put a washer (6) between them. Then press the lever (1) so that
the spherical end can entre into the pivot (5) . Then tighten the screw (3) on the frame using a tapered washer (7) and 1 nut (8). Complete the assembly
inserting a a pin (9) into the hole placed on the pivot (5) .
! ! ! ! !
ASSEMBLY OF THE WIDENING TINE AND TREE-SAVER DISK (Fig. 11)
the hole which is placed on the tines (assembled), please make the parts on which you can see the fixing holes to correspond. Then tighten using a
screw M10X45 (3) and a nut (4). Take the tree disk –saver (5) and insert it the same way into the end part of the widening tine (1) making the fixing holes
to correspond and fix it with a screw M10X40 (6) and the nut (7) . Every widening tine can be assembled indifferently both on right and left sides .
! ! ! ! !
ASSEMBLY ON THE WIDENING TINE – TINE PROTECTION (Fig. 12)
tines protection (2) which is already assembled on the frame ,making it to correspond to the fixing holes. Then fix it using the screws (3) washers (4)
8
and nuts (5), please make attention to the fact that the widening tines are not the same but they are symmetrical.
The driving cables are supplied assembled with the unit . You
Inser the gearbox lever (1) inside the slot (2) you can find on the frame , making the
Insert the hexagonal end part of the widening (1) into
Please position the widening tine – protection (1) under the
Bring the drive throttle handle all its way (1). It is
Repeat the procedure described in the
The throttle cable is supplied already fixed on the
Bring the drive throttle handle all its