En: Installation Instructions; Technical Data - Interlogix DC148R4.7 Instrucciones De Instalación

EN: Installation Instructions

Legend for Figures
1 Magnetic contact
2 Installation and connection diagram
A Contact
B Magnet
C Stud
3 Distance diagram
A Proximity/switch-on distance
B Distance/switch-off clearance
C Failure range/tamper range
D Tolerance zone
E Contact
F Magnet
G Stud
4 Connection
A, B Connection cable
C Switching part (NC)
D Tamper protection (internal reed)
Description
The magnetic contact and the magnet are mounted parallel to
each other with the aid of the surface-mounted or flush-
mounted housing. When inserting the contact housing, please
ensure that the labeling stud on the front is pointing toward the
magnet, regardless of the type of installation.
The installation distance between the contact and the magnet
must be within the tolerance zone (see distance diagram).
During installation within the tolerance zone, the switching
distances for each contact must first be individually determined
(see distances diagram).
Caution: Installation on ferromagnetic materials is only
permissible if the contact and magnet housing are each fitted
with a 2 mm base.
Surface-mounted or flush-mounted parts must only be
mounted using screws made of non-magnetic material. When
the installation is completed, the electrical switch function of
the magnetic contact must be checked (e.g. with a continuity
checker or multimeter). Use of mechanical force, e.g., when
installing on the housing, can damage the glass body of the
reed switches.
The covers are then clipped onto the
surface-mounted housing. The covers can
be reopened with a small screwdriver
(max. 3 mm) without incurring any
damage. To do this, press in the small
snap-fit hook on the front using the
screwdriver. In accordance with VdS,
unauthorized opening must be made detectable by placing the
VdS seal sticker (Fig. 1) on the snap-fit hook.
Caution: Measure the supply lines electrically before
connecting them!
2 of 12
Distance Diagram
See Figure 3.
Note: When installing the devices on ferromagnetic materials,
the contact and magnet housing must each be fitted with a 2
mm base.
Ø
Magnet 8x30 mm
Non ferromagn. installation
Proximity/switch-on distance
Distance/switch-off clearance
Failure range/tamper range
Minimum switch-on distance: 15 mm,
Tolerance in x: max. +/- 2 mm
Ø
Magnet 8x30 mm
Ferromagn. installation
Proximity/switch-on distance
Distance/switch-off clearance
Failure range/tamper range
Minimum switch-on distance: 8 mm,
Tolerance in x: max. +/- 2 mm

Technical Data

Surface-mounted magnetic contact DC148R4.7 for EOL zone
types, tamper protected, for parallel surface-mounted
installation; with 2 integrated 4k7 resistors.
Contact type 1 - pin NC contact
Switching distance min. 15 mm
Switching voltage max. 100 V DC
Switching current max. 500 mA
Contact rating max. 6 W or 6 VA
Contact resistance max. 0.15 Ohm
Breakdown voltage > 250 V
Permissible operating max. 40 V
voltage
Connection cable LIYY 2 x 0.14 mm Cu tin-plated;
Suitable for LSA IDC method of termination
External cable color White
Internal conductor Blue
Contact dimensions 8 x 8 x 40 mm
Ø 3.2 mm x 2 m
Cable dimensions
Ø 8 x 30 mm AlNiCo 5, axially polarized
Magnet
Housing dimensions 54 x 13 x 12.5 mm
Housing material S-B or A-B-S
Color White
− 25°C to + 70°C
Temperature range
Protection category VdS - environmental class III, IP 67
Scope of Delivery
•
1 magnetic contact 8 x 8 x 32 mm
•
Ø
1 magnet 8 x 30 mm AlNiCo 5
•
2 surface-mounted housings
P/N 31496300.Y71 • REV 4 • ISS 18MAR19
Switch-on Tolerance
distance [mm] [mm]
19 +/- 4
23 +/- 3
7 +/- 3
Switch-on Tolerance
distance [mm] [mm]
12 +/- 4
14 +/- 3
2 +/- 2